Bedienungsanleitung Intex Easy Set 305x61 (Seite 7 von 12) (Englisch)

752269

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

86A

S AVE THESE INSTRUCTIONS

(86IO) EASY SET POOL ENGLISH 7.5” X 10.3” PANTONE 295U 07/11/2017

English

Page 7

3. Hose connectors

• The following applies to pool liners with hose connectors (16" (488 cm) & below pools). If the pool was

purchased

without a filter pump, insert two black plugs (2) into the black filter pump outlets. Do this from

the inside of the pool so that water will not run out when filling it.

• If the pool was purchased with a filter pump, read the Krystal Clear™ Filter Pump Manual first and then

proceed to next installation step.

POOL SETUP (continued)

IMPORTANT

Proper inflation of the top ring.

The ambient temperatures of air and water have an effect on the internal pressure of the top ring.

To maintain a correct internal pressure, it is best to leave some room for expansion as the sun

heats the air inside the ring. During very hot weather, you must check to see whether it is necessary

to release some air. This is to avoid any possible damage to the ring.

In no event shall Intex, their authorized agents or employees be liable for damages (such

as pin holes) to the inflatable top ring caused by negligence, ordinary wear and tear, abuse

and carelessness, or external forces.

You may have purchased this pool with the Intex Krystal Clear™ filter pump. The pump has its

own separate set of installation instructions. First assemble your pool unit and then set up the

filter pump.

Estimated assembly time 10~30 minutes. (Note the assembly time is only approximate and

individual assembly experience may vary.)

1. Liner preparation

• Find a flat, level location that is free and clear of stones, branches or other sharp objects that may

puncture the pool liner or cause injury.

• Open the carton containing the liner, etc., very carefully as this carton can be used to store the pool

during the winter months or when not in use.

• Take out the ground cloth (3) and spread it over the cleared

area. Then take out the liner (1) and spread it out over the

ground cloth, with the drain valve directed towards the draining

area. Place the drain valve away from the house.

IMPORTANT: Always set up the pool unit with at least 2

persons. Do not drag the liner across the ground as this can

cause liner damage and pool leakage (see drawing 2).

• During the setup of the pool liner, point the hose connections

or openings in the direction of the electrical power source. The

outer edge of the pool should be within reach of the pump’s

electrical connection.

• Lay out the pool. Spread out the plain blue sides and make the

pool floor as smooth as possible (see drawing 2).

2. Ring inflation

• Flip the top ring out and check that it is fully outside of the wall

lining and facing up. Inflate the ring with a manual air pump (see

drawing 3). Keep the top ring centered in the middle of the pool,

while doing this.

IMPORTANT: Prevent bursting by not using a

high-pressure pump, such as an air compressor. Do not

over inflate. Preferably use an Intex manual inflation hand

pump (not included).

WATER

LEVEL

Level

FILL LINE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Easy Set 305x61 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex Easy Set 305x61

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info