Bedienungsanleitung Intex ECO 5110 (Seite 11 von 27) (Englisch)

686154

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

(329PO) MODEL ECO5110&6110 SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2017

329

SAVE THESE INSTRUCTIONS

English

Page 11

SALT & POOL WATER VOLUMES

• Which kind of salt to use:

Use only Sodium Chloride Salts

Use only sodium chloride (NaCl) salt that is at least 99.8% pure. It is also acceptable to use

water conditioning salt pellets (the compressed forms of evaporated salt). However, it will take a

longer time for them to dissolve.

Do not use iodized or yellow (yellow prussiate of soda) colored salt.

Salt is added to the pool water and the electrolytic cell uses the salt to create chlorine. The purer

the salt the better the performance of the electrolytic cell.

• Optimum Salt Levels

The ideal salt level in the pool water is between 2500-3500 ppm (parts per million). The optimal

level is 3000 ppm.

A too low salt level will reduce the efficiency of the Saltwater System and result in low chlorine

production. A high salt level may generate a salty taste to the pool water (this may occur at a salt

level above 3500-4000ppm). Too high a salt level may damage the power supply and cause

corrosion to the pool metal fixtures and accessories. The Salt Table page of this manual, shows

the correct dosage of salt needed. The salt in the pool is constantly recycled. The loss of salt is

due only to pool water being physically removed from the pool. Salt is not lost due to

evaporation.

• Adding Salt

. Switch the filter pump on to start the water circulation.

. Keep the Saltwater System turned off.

. Determine the amount of salt to be added (see “Salt Table”).

. Evenly spread the proper amount of salt around the inside perimeter of the pool.

. Avoid clogging the filter. Do not add salt through the skimmer.

. Brush the pool bottom to speed up the dissolving process. Do not allow salt to pile up on the

bottom of the pool. Run the filter pump 24 consecutive hours to thoroughly dissolve the salt.

. After 24 hours and if all the salt is dissolved, turn on the Saltwater System, press

button

until you hear a “beep”, code “00” flashing and set the saltwater pool system to desired

operating time (see “Operating Time Table”).

• Removing Salt

If too much salt has been added, the unit will beep and display “Code 92” (see “Alarm Codes”).

You will need to lower the salt concentration. The only way to do so, is to partially drain the pool

and refill it with fresh water. Drain and refill approximately 20% of the pool’s water until the “Code

92” disappears.

• Pool Volume Calculation

Rectangular

Length x Width x Average Depth x 7.5 Length x Width x Average Depth

Circular

Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79

Oval

Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80

Types of Pool

Gallons

(pool size in feet)

Cubic Meters

(pool size in meters)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex ECO 5110 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info