Bedienungsanleitung Intex ECO 5110 (Seite 18 von 27) (Englisch)

686154

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

(329PO) MODEL ECO5110&6110 SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2017

329

SAVE THESE INSTRUCTIONS

English

Page 18

OPERATION INSTRUCTIONS (continued)

Boost cycle

•

First time installation, press and hold “BOOST” button for 5 seconds

until the indicator lights up and the LED display “80”. This indicates

that the saltwater system has started E.C.O. and more chlorine

sanitizer production. You can press and hold the “BOOST” button for

another 5 seconds until the indicator is off, which will cancel the Boost

cycle.

•

The boost operating hours is 8 times the amount of time programmed into the system, i.e. if

your saltwater system operating time is 2 hours, the boost procedure will run 8 x 2 = 16 hours.

After boost procedure has been completed, the system will automatically switch to the

normal working mode.

•

Once the boost is operating, check whether the filter pump operating hours have been

set properly. For example, the boost operating time is 8 hours, the filter pump should be

set to run for 8 hours at least. Increase the filter pump operating time if necessary.

Note:

If an Intex filter pump is attached to the system, set the pump switch to on “I”

position.

•

After a heavy rain or if the pool is dirty, press the “BOOST” button to

shock the pool again.

Stand-by/power saving mode:

•

When the cycle ends, the green “SLEEP” indicator on the control

panel lights up and the LED display flashes “93”. The system is now

in Stand-By mode. After a while, it shuts down and sets itself in a

Power Saving mode. The system will automatically turn itself back

on in 24 hours, starting its daily cycle of chlorine production.

•

The “SLEEP” indicator stays on, while the system is in the Power

Saving mode. The LED display however, goes blank after 5 minutes.

Press any button (

or ) to view the last LED code.

Electrode Self-Clean cycle:

•

Press and hold button for 5 seconds until the LED display flashes

“10”. Depending on your pool water calcium hardness level, press

button again to select the self-clean cycle time as below. Total of 3

settings: 14 hours, 10 hours and 06 hours.

NOTE:

The life of the cell varies depending on water conditions, pool usage and

operating time of the device. Select 14 hours cycle time to maximize the life of the

electrolytic cell if the calcium hardness level is up to 150 ppm. Manual routine cleaning

and maintenance will further lengthen the life of the electrolytic cell.

•

With the desired self-clean hours showing, press

button to lock the keypad controls

and the LED display will return to the normal operating time. The system will reverse the

polarity of the electrode

(5)

every time according to the selected hours.

NOTE:

If you forget to lock the keypad controls, the system will automatically lock it and

start working 5 seconds later.

Calcium Hardness Self-clean cycle time

0 - 150 ppm Reverse polarity every 14 hours

150 - 250 ppm Reverse polarity every 10 hours

250 - 350 ppm Reverse polarity every 06 hours

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex ECO 5110 Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info