Bedienungsanleitung Intex ECO6220G (Seite 18 von 28) (Englisch)

686079

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

329

SAVE THESE INSTRUCTIONS

English

(329IO) MODEL ECO 5220/5230 & 6220/6230 SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 06/05/2018

Page 18

OPERATION INSTRUCTIONS (continued)

6. Boost cycle

• First time installation, press and hold “BOOST” button for 5 seconds until

the indicator lights up and the LED display “80”. This indicates that the

saltwater system has started more chlorine sanitizer production. You can

press and hold the “BOOST” button for another 5 seconds until the indicator

is off, which will cancel the Boost cycle.

• The boost operating hours is 8 times the amount of time programmed into the

system, i.e. if your saltwater system operating time is 2 hours, the boost procedure will run 8 x 2 =

16 hours. After boost procedure has been completed, the system will automatically switch to

the normal working mode.

• Once the boost is operating, check whether the filter pump operating hours have been set

properly. For example, the boost operating time is 8 hours, the filter pump should be set to

run for 8 hours at least. Increase the filter pump operating time if necessary.

NOTE: If an Intex filter pump is attached to the system, set the pump switch to on “I”

position.

• After a heavy rain or if the pool is dirty, press the “BOOST” button to shock

the pool again.

7. Stand-by/power saving mode:

• When the cycle ends, the green “SLEEP” indicator on the control panel

lights up and the LED display flashes “93”. The system is now in Stand-By

mode. After a while, it shuts down and sets itself in a Power Saving mode.

The system will automatically turn itself back on in 24 hours,

starting its daily cycle of chlorine production.

• The “SLEEP” indicator stays on, while the system is in the Power Saving

mode. The LED display however, goes blank after 5 minutes. Press any

button ( or ) to view the last LED code.

8. Electrode Self-Clean cycle:

• Press and hold button for 5 seconds until the LED display flashes

“10”. Depending on your pool water calcium hardness level, press

button again to select the self-clean cycle time as below. Total of 3

settings: 14 hours, 10 hours and 06 hours.

NOTE: The life of the cell varies depending on water conditions, pool usage and operating

time of the device. Select 14 hours cycle time to maximize the life of the electrolytic cell if

the calcium hardness level is up to 150 ppm. Manual routine cleaning and maintenance will

further lengthen the life of the electrolytic cell.

• With the desired self-clean hours showing, press button to lock the keypad controls and

the LED display will return to the normal operating time. The system will reverse the polarity

of the electrode (5) every time according to the selected hours.

NOTE: If you forget to lock the keypad controls, the system will automatically lock it.

Calcium Hardness Self-clean cycle time

0 - 150 ppm Reverse polarity every 14 hours

150 - 250 ppm Reverse polarity every 10 hours

250 - 350 ppm Reverse polarity every 06 hours

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex ECO6220G Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex ECO6220G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info