Bedienungsanleitung Intex Krystal Clear - 602G (Seite 9 von 11) (Englisch)

686080

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

(257GS) MODEL 602G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/17/2015

257

SAVE THESE INSTRUCTIONS

English

Page 9

TROUBLESHOOTING GUIDE

IMPORTANT

If you continue to experience difficulty, please contact our Consumer Service

Department for assistance. See separate "Authorized Service Centers" sheet.

FILTER MOTOR

FAILS TO START

FILTER DOESN’T

CLEAN POOL

FILTER DOESN’T PUMP

WATER OR FLOW IS

VERY SLOW

PUMP DOESN’T WORK

TOP COVER

LEAKING

HOSE LEAKING

AIR LOCK

• The motor is not plugged in.

• The GFCI/RCD circuit breaker

is tripped.

• Motor too hot and overload

protection is shut off.

• Improper chlorine or pH

levels.

• Filter cartridge is dirty.

• Damaged cartridge.

• Excessively dirty pool.

• The strainer screen is

restricting the water flow.

• Clogged inlet or discharge.

• An air leak on the intake line.

• Scale or buildup on cartridge.

• Excessively dirty pool.

• Dirty filter cartridge.

• The nozzle and strainer

connection are reversed.

• Low water level.

• Strainer screen plugged up.

• An air leak on the intake hose.

• Faulty motor or the impeller is

jammed.

• An air lock inside the

cartridge chamber.

• O-ring missing.

• Cover or air release valve are not

tight.

• Hose clamps are not well-fitted.

• Hose o-ring dislodged when

connecting the hose.

• Hose broken.

• There’s air trapped in the pump

housing and inlet hose.

TROUBLE CAUSE SOLUTION

• Filter cord must be plugged into a 3

wire outlet that is protected by a Class A

Ground Fault Circuit Interrupter, or RCD.

• Reset circuit breaker. If circuit breaker

trips repeatedly, your electrical system

may have a defect. Turn off circuit breaker

and call an electrician to correct the problem.

• Let the motor cool down.

•

Adjust the chlorine and pH level. Consult

your local swimming pool supply stores.

•

Clean or replace cartridge.

•

Check the cartridge for holes. Replace if

damaged.

•

Operate the filter for longer periods.

•

Clean the strainer screen at the inlet.

• Clear any obstructions in the intake hose by

discharging it inside pool wall.

• Tighten hose clamps, check hoses for

damage, check pool water level.

• Replace cartridge.

• Clean cartridge more often.

• Install the nozzle at the upper position of the

pool inlet, and the strainer at the lower

position of the pool outlet.

• Fill pool to correct water level.

• Clean strainer screens at pool inlet.

• Tighten hose clamps, check hose for

damage.

• Clear any sticks or leaves in the intake

hose.

• Open the release valve at top of pump.

• Remove cover & check for O-ring.

• Tighten cover or valve (Manually).

• Tighten or change hose clamps.

• Put the o-ring back into the groove.

• Replace a new hose.

• Open air release valve, lift and lower the

inlet hose until water starts to flow out of

the air release valve, close air release valve.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Krystal Clear - 602G Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex Krystal Clear - 602G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info