Bedienungsanleitung Intex Krystal Clear - CS7220G (Seite 13 von 29) (Englisch)

752330

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

188

SAVE THESE INSTRUCTIONS Page 2

English

(188NL) MODEL CS7220G SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 09/28/2012

SAVE THESE INSTRUCTIONS Page 13

English

SALT & POOL WATER VOLUMES

• Which kind of salt to use:

Use only Sodium Chloride Salts

Use only sodium chloride (NaCl) salt that is at least 99.8% pure. It is also

acceptable to use water conditioning salt pellets (the compressed forms of

evaporated salt). However, it will take a longer time for them to dissolve.

Do not use iodized or yellow (yellow prussiate of soda) colored salt.

Salt is added to the pool water and the electrolytic cell uses the salt to create

chlorine. The purer the salt the better the performance of the electrolytic cell.

• Optimum Salt Levels

The ideal salt level in the pool water is between 2500-3500 ppm (parts per million).

The optimal level is 3000 ppm.

A too low salt level will reduce the efficiency of the Saltwater System and result

in low chlorine production. A high salt level may generate a salty taste to the pool

water (this may occur at a salt level above 3500-4000ppm). Too high a salt level

may damage the power supply and cause corrosion to the pool metal fixtures and

accessories. The Salt Table page of this manual, shows the correct dosage of salt

needed. The salt in the pool is constantly recycled. The loss of salt is due only to

pool water being physically removed from the pool. Salt is not lost due to

evaporation.

• Adding Salt

1. Switch the filter pump on to start the water circulation.

2. Keep the Saltwater System turned off.

3. Determine the amount of salt to be added (see “Salt Table”).

4. Evenly spread the proper amount of salt around the inside perimeter of the

pool.

5. Avoid clogging the filter. Do not add salt through the skimmer.

6. Brush the pool bottom to speed up the dissolving process. Do not allow salt to

pile up on the bottom of the pool. Run the filter pump 24 consecutive hours to

thoroughly dissolve the salt.

7. After 24 hours and if all the salt is dissolved, turn on the Saltwater System,

press button until you hear a “beep”, code “00” flashing and set the saltwater

pool system to desired operating time (see “Operating Time Table”).

• Removing Salt

If too much salt has been added, the unit will beep and display “Code 92” (see “Alarm

Codes”). You will need to lower the salt concentration. The only way to do so, is to

partially drain the pool and refill it with fresh water. Drain and refill

approximately 20% of the pool’s water until the “Code 92” disappears.

• Pool Volume Calculation

Rectangular

Length x Width x Average Depth x 7.5 Length x Width x Average Depth

Circular

Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79

Oval

Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80

Types of Pool Gallons

(pool size in feet) Cubic Meters

(pool size in meters)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Krystal Clear - CS7220G Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex Krystal Clear - CS7220G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info