Bedienungsanleitung Intex Krystal Clear 601 (Seite 5 von 11) (Englisch)

686150

Zoom out

Zoom in

Vorherige Seite

1/11

Nächste Seite

257

SAVE THESE INSTRUCTIONS

English

(257PO) MODEL 601 FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 04/22/2016

Page 5

Be sure you have access to water to fill the pool and chemicals for the water.

IMPORTANT: This filter pump is shipped with the air release valve (1) open (open the air

release valve if necessary). DO NOT replace the air release valve until you reach STEP #8.

Failure to follow these instructions will result in air trapped inside filter housing; the motor

will run dry, be noisy and malfunction.

Assemble above-ground-pool first. Carefully follow the pool’s installation instructions.

Place the filter pump the length of the hose away from the pool wall where the lower black

protruding hose connection is "sticking-out".

Insert the nozzle union

(13 & 10)

into the upper protruding hose connections, and then

attach the pool inlet air adaptor

(15)

to the upper protruding fitting. Screw the air jet valve

(14)

over the pool inlet air adaptor

(15).

Then insert the strainer union

(9 & 11)

into the lower

protruding hose connections. The hoses

(8)

fit over the strainers inserted into the connections.

There are two hoses to be connected to the filter pump hose connections. With hose clamps

(7)

fasten one of the hoses

(8)

to the lower protruding hose connection (marked "+" on the pool

liner) and to the upper pump connection (marked "+").

Connect the second hose to the pool inlet air adaptor

(15)

and to the lower pump

connection. Make sure all the hose clamps

(7)

are tight.

NOTE:

Make sure the air jet

valve

(14)

is securely tighten onto the pool inlet air adaptor

(15)

and facing up.

In a counter-clockwise motion unscrew the threaded filter housing collar

(12)

from the filter

housing.Graspandremovethe housing cover

(3)

. Check to see if a cartridge is inside the

housing. If yes, replace the cover, finger tighten the housing collar

(12)

back onto the filter

housing.

Fill the pool to a level of at least 1-2 inches above the top connection. The water will

automatically flow down into the pump.

When water starts flowing out of the air release valve hole, screw in the air release valve back

into the filter housing cover. Do not over tighten the valve.

NOTE: Venting the system is

necessary for air to escape as the filter housing fills with water.

Connect the filter pump to the power outlet. The filter pump is now filtering the water.

10.

Operate the filter pump until the desired water clarity is obtained.

NOTE:

Never put pool chemicals directly into the filter pump. This may damage the pump

and void the warranty.

SETUP INSTRUCTIONS

(ILLUSTRATION NOT TO SCALE)

WATER LEVEL

POOL INLET

JET NOZZLE

(REMOVE)

HOSE CLAMP

INSIDE OF POOL

STRAINER GRID

(REMOVE)

PLUG

UPPER PUMP

CONNECTION

LOWER PUMP

CONNECTION

FILTER

CARTRIDGE

INSIDE

AIR RELEASE

VALVE

HOSE

POOL INLET

AIR ADAPTOR

AIR JET

VALVE

FILTER HOUSING

COVER

THREADED FILTER

HOUSING COLLAR

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Krystal Clear 601 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info