Bedienungsanleitung Intex Krystal Clear 636G (Seite 14 von 17) (Englisch)

686600

Zoom out

Zoom in

Vorherige Seite

1/17

Nächste Seite

(108GS) MODEL 636G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/02/2012

108

SAVE THESE INSTRUCTIONS

Page 14

English

TROUBLESHOOTING GUIDE

IMPORTANT

If you continue to experience difficulty, please contact our Consumer Service

Department for assistance. See separate “Authorized Service Centers” sheet.

FILTER MOTOR

FAILS TO START

FILTER DOESN’T

CLEAN POOL

FILTER DOESN’T

PUMP WATER OR

THE WATER FLOW

IS VERY SLOW

PUMP DOESN’T

WORK

TOP COVER

LEAKING

HOSE LEAKING

AIR LOCK

• The motor is not plugged in.

• The Fuse box needs checking.

• The GFCI/RCD circuit breaker

is tripped.

• Motor too hot and overload

protection is shut off.

• Improper chlorine or pH

levels.

• Filter cartridge is dirty.

• Damaged cartridge.

• Excessively dirty pool.

• The strainer screen is

restricting the water flow.

• Clogged inlet or discharge.

• An air leak on the intake line.

• Scale or buildup on cartridge.

• Excessively dirty pool.

• Dirty filter cartridge.

• The nozzle and strainer

connection are reversed.

• Low water level.

• Strainer screen plugged up.

• An air leak on the intake hose.

• Faulty motor or the impeller

is jammed.

• An air lock inside the cartridge

chamber.

• O-ring missing.

• Cover is not tight.

• Filter cartridge is dirty.

• Hose nuts are not well-fitted.

• There’s air trapped in the

pump housing and inlet hose.

• The inlet and outlet hoses

connection are reversed.

TROUBLE CAUSE SOLUTION

•

Filter cord must be plugged into a 3 wire

outlet that is protected by a Class A

Ground Fault Circuit Interrupter, or RCD.

• Reset circuit breaker. If circuit breaker

trips repeatedly, your electrical system

may have a defect. Turn off circuit

breaker and call an electrician to

correct the problem.

• Let the motor cool down.

•

Adjust the chlorine and pH level.

Consult your local swimming pool

supply stores.

• Clean or replace cartridge.

• Check the cartridge for holes. Replace

if damaged.

• Operate the filter for longer periods.

• Clean the strainer screen at the inlet.

• Clear any obstructions in the intake

hose by discharging it inside pool wall.

• Tighten hose nuts, check hoses for

damage, check pool water level.

• Replace cartridge.

• Clean cartridge more often.

• Clean inside the plunger valve.

•

Pull valve handle to full upright position.

• Install the nozzle at the upper position

of the pool inlet, and the strainer at the

lower position of the pool outlet.

• Fill pool to correct water level.

• Clean strainer screens at pool inlet.

• Tighten hose nuts, check hose for damage.

• Clear any sticks or leaves in the

intake hose.

• Turn and pull valve handle to full

upright position.

• Remove cover & check for O-ring.

• Tighten cover (Manually).

• Replace or clean cartridge.

• Tighten or reinstall hose nut.

• Open air release valve, wait until water

starts to flow out of the valve, then

close it.

• The lower position of pool outlet

connects to filter pump water inlet. The

upper position of pool inlet connects to

filter pump water outlet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Krystal Clear 636G Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex Krystal Clear 636G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info