Bedienungsanleitung Intex Krystal Clear SF60220-1 (Seite 16 von 23) (Englisch)

686135

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

195A

SAVE THESE INSTRUCTIONS

(195IO) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/03/2015

English

Page 16

OPERATING INSTRUCTIONS (continued)

Switch off the pump, change the 6-way valve to “RINSE” position

(see drawing 25)

Switch on the pump and run the pump for about one minute to level out the sand bed after

backwashing the sand media.

Switch off the pump, change the 6-way valve to “FILTER” position

(see drawing 23)

Switch on the pump. The system is now operating in the normal filtering mode. Run the pump

until the desired pool water clearance is obtained and no more than 12 hours per day.

Record the initial pressure gauge reading when the filter media is clean.

NOTE:

During initial setup of the system, it may be necessary to backwash frequently due to

unusual heavy dirt present in the water and sand. After that, as the filter removes dirt and

impurities from the pool water, the accumulated dirt in the sand media will cause the pressure

to rise and the flow to diminish. If there is no vacuuming device attached to the system and

the pressure gauge reading is in the yellow zone it is time to backwash the sand media, see

“BACKWASH” under “initial startup and operation” section.

Vacuuming device (i.e. Intex auto pool cleaner) attached to the system may also cause the

flow to diminish and the pressure to rise. Remove any vacuuming device from the system and

check if the pressure gauge reading has dropped from the yellow zone to the green zone.

10.

Monitor the pressure gauge reading, and check that the inlet and outlet openings are not

obstructed on a weekly basis. If the pressure gauge indicates yellow it is time to backwash

the filter media.

Operating the system under “TIMER” mode or manually:

To operate the sand filter pump in “FILTER” mode under “TIMER” control:

A. Set the timer dial to the desired operating hours. See operation time table

(see drawing 31)

B. Turn on the pump by pressing the switch to “ ” position, the sand filter pump is now

filtering the water and will stop after the operating hours are completed. The built-in timer

will now operate for the number of hours selected at the same time each day.

C. Operating hours can be re-adjusted if necessary. Follow step A – B.

To operate the sand filter pump manually (without the “TIMER” mode):

A. Turn on the pump by pressing the switch to “-” position, the sand filter pump is now

filtering the water.

B. To turn off the pump, press the switch to “O” position.

IMPORTANT

If you continue to experience difficulty, please contact our Consumer Service

Department for assistance. See separate “Authorized Service Centers” sheet.

TIMER

OFF

TIMER DIAL

(HOURS)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Krystal Clear SF60220-1 Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex Krystal Clear SF60220-1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info