Bedienungsanleitung Intex Krystal Clearl 638G (Seite 6 von 14) (Englisch)

686601

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

(106GS) MODEL 638G FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/10/2012

106

SAVE THESE INSTRUCTIONS Page 6

English

SETUP INSTRUCTIONS

Be sure you have access to water to fill the pool and chemicals for the water. A

small coin can be used to tighten the hose clamps (7).

IMPORTANT: This filter pump is shipped with the air release valve (1) open

(open the air release valve if necessary). DO NOT replace the air release valve

until you reach STEP #8. Failure to follow these instructions will result in air

trapped inside filter housing; the motor will run dry, be noisy and malfunction.

1. Assemble above-ground-pool first. Carefully follow the pool’s installation

instructions.

2. Place the filter pump the length of the hose away from the pool wall where the

lower black protruding hose connection is "sticking-out".

3. Insert the nozzle union (9 & 10) into the upper protruding hose connections.

Then insert the strainer union (9 & 11) into the lower protruding hose

connections. The hoses (8) fit over the strainers inserted into the connections.

4. There are two hoses to be connected to the filter pump hose connections. With

hose clamps (7), fasten one of the hoses (8) to the lower protruding hose

connection (marked "+" on the pool liner) and to the upper pump connection

(marked "+").

5. Connect the second hose to the remaining upper protruding hose connection

and to the lower pump connection. Make sure all the hose clamps (7) are tight.

6. Twist the filter pump’s threaded cover (3) in a clockwise direction to be sure it

is on "tight". Use only your hands to tighten the top. Do not tighten with tools

such as pliers.

7. Fill the pool to a level of at least 1-2 inches above the top connection. The

water will automatically flow down into the pump.

8. When water starts flowing out of the air release valve hole, screw in the air

release valve back into the filter housing cover. Do not over tighten the valve.

NOTE: Venting the system is necessary for air to escape as the filter

housing fills with water.

9. Connect the filter pump power cord end to the transformer output receptacle

and screw in the cover. Plug the transformer power cord into a properly

installed electrical socket.

10. Operate the filter pump until the desired water clarity is obtained.

WARNING

Risk of electric shock. Connect transformer only to a grounding type

receptacle protected by a ground-fault circuit interrupter (GFCI) or

residual current device (RCD). Contact a qualified electrician if you cannot

verify that the receptacle is protected by a GFCI/RCD. Use a qualified

electrician to install the GFCI/RCD, which has a maximum rate of 30mA.

Do not use a portable residual current device (PRCD).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Krystal Clearl 638G Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex Krystal Clearl 638G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info