Bedienungsanleitung Intex Metal Frame - 28235 (Seite 12 von 19) (Englisch)

686103

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

87PO

SAVE THESE INSTRUCTIONS

English

(87PO) ROUND METAL FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 05/25/2016

Page 12

POOL SETUP (continued)

YoumayhavepurchasedthispoolwiththeIntexKrystalClear™filterpump.Thepumphasitsown

separate set of installation instructions. First assemble your pool unit and then set up the filter pump.

Estimatedassemblytime30-60minutes.(Notetheassemblytimeisonlyapproximateandindividual

assemblyexperiencemayvary.)

1. Liner preparation

• Findaflat,levellocationthatisfreeandclearofstones,branchesorothersharpobjectsthatmay

puncture the pool liner or cause injury.

• Openthecartoncontainingtheliner,joints,legs,etc.,verycarefullyasthiscartoncanbeusedtostore 

the pool during the winter months or when not in use.

• Takeoutthegroundcloth

(10)

(optional)andspreaditover

the cleared area. Then take out the liner

(7) and spread it

out over the ground cloth, with the drain valve directed

towards the draining area. Place the drain valve away from

the house. Allow the sun to warm up the liner before

inserting the beams

(6) into the sleeve openings.

IMPORTANT: Always set up the pool unit with at least 2

persons. Do not drag the liner across the ground as

this can cause liner damage and pool leakage (see

drawing 1).

• Duringthesetupofthispoolliner,pointthehoseconnectionsoropeningsinthedirectionoftheelectric 

 powersource.Theouteredgeofthepoolshouldbewithinreachofthepump’selectricalconnection.

2. Frame assembly

• Theframepool’slegs

(8) and beams (6)

fallintotwogroups.Thelargerdiametersarethehorizontal 

 beamsthatareslid(pushed)intothesleeveopeningsatthetopoftheliner.Thesmallerdiametersare 

the vertical legs. Both these legs and beams fit into the T-joints

(3).

• Startingatanylocation,butalwaysworkinginthesamedirection,push

 thehorizontalbeamintothesleeve.Oncethebeamiscenteredtake

one of the T- joints and using the connection pin

(1)

, attach the joint to

one end of the beam by inserting the pin through the seal

(2)

and in the

pre-drilled holes. Repeat this procedure in a circular fashion until all the

beams and joints have been connected

(see drawing 2.1).

The last joint connection may be difficult to complete. You can do

it though, if you first simultaneously raisethe last joint and beam

about 2 inches (5 cm). Now insert the beam into the joint while

lowering the pieces into position. The beam will easily slide into

the joint (see drawing 2.2). Ensure that the last joint is fully

connected before proceeding to connecting the legs.

2.1

2.2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Metal Frame - 28235 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info