686122
11
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
254
PO
S AVE THESE INSTRUCTIONS
(254PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/31/2018
English
Page 11
SET UP
(continued)
Spa Control Unit Installation
1.
Connect the spa control unit to the spa tub
(see drawing 10)
. Hand-tighten the connectors securely.
Do not use tools to tighten.
2.
Reinstall the back cover
(2)
to the spa control base
(see drawing 11)
.
CAUTION:
Back cover must be installed before using the SPA.
Do not sit, lean, cover or place
any objects over the spa control unit.
3.
Attach the two lter cartridge housing assemblies to the two outlet
grids on the inside of the spa (lower position, marked “C”). In ate
the spa tub rst before installing lter pump ttings.
ATTENTION!
In order to comply with the requirements of the
Virginia Grahame Baker Act, suction outlets cannot be covered
while the spa is in use. The Act was intended to address high
suction/volume circulation systems but does not exclude low
volume systems as used on this spa. Accordingly, remove the lter
cartridge assemblies and any other spa cleaning attachment from
the spa outlets before spa usage
(see drawing 12)
.
Re-attach them after usage for water ltration and cleaning.
4.
Before lling with water ensure the bottom drain valve caps are
securely closed on the inside and outside.
5.
Fill the spa tub with freshwater to a level between MIN and MAX
marked on the inside of the spa wall. Do not over ll the spa. Never
move the spa tub with water inside and/or with the control base attached to the spa as the spa or
control base may be damaged.
WARNING:
Never pour water with a temperature higher than 104°F (40°C) into the spa directly. It is
recommended to ll the spa tub with lukewarm water for quick heating and energy saving.
6.
Place the spa cover and spa air bladder (pre-installed in spa cover) over the spa tub, and make sure the
spa cover buckles are locked using the key provided after pulling the buckled straps tight.
IMPORTANT:
Inspect the spa cover regularly for leak, premature wear and tear or deterioration. Never
use a damaged spa cover.
7.
Ensure the spa is plugged into a grounded electrical socket and press the button to turn on the
control unit panel buttons rst. Press the button on the control panel to activate the heater, see “Spa
Control Unit Panel” operation section.
12
C
11
2
10
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Intex Pure Spa 28403 - SSP-H-10-2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info