Bedienungsanleitung Intex PureSpa - SJB-HS-30-1C (Seite 26 von 27) (Englisch)

686044

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

264

S AVE THESE INSTRUCTIONS

(264IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 10/07/2015

English

Page 26

TROUBLESHOOTING (continued)

LED PANEL

CODE PROBLEM SOLUTION

LED Panel Code Flash & Alarm On (NOTE: Always turn off the power before cleaning and servicing).

E90

• No water ﬂ ow.

• Turn off and unplug the control unit.

• Ensure the outlet cover grid is clean and free from obstructions.

• Clean or replace the cartridge, see Maintenance and Storage section.

• Ensure the in/outlet connections on the spa tub and ﬁ lter pump are not

blocked.

• Keep the spa water properly sanitized to ensure a clean and unclogged

ﬁ lter cartridge.

• Press the button to turn off the unit. Release trapped air by

unscrewing the drain valve cap on the control base side with a coin.

Air has been release once a steady stream of water is ﬂ owing out from

the drain valve. Wait for 15 seconds and screw the drain valve cap

back. Press the button to activate the control panel buttons, and

then run the ﬁ lter function by pressing the button to push out any

remaining air in the system.

• If problem persists, contact Intex Service Center.

E91

• Dirt or scale on titanium plates.

• Low salt level / No salt.

• Electrolytic cell cord is loose.

• Possible electrolytic cell failure.

• Remove the electrolytic cell for inspection. Clean it if necessary. See

“Maintenance”.

• Add salt. See “Salt Level Information”.

• Ensure that the cell cord is plugged ﬁ rmly into the cell receptacle.

• Contact Intex Service Center. Replace the cell if needed.

E92 • High salt level.

• Partially drain the pool and reﬁ ll it with fresh water. See “Salt Level

Information”.

E94

• Water temperature too low.

• If the ambient temperature is below 4°C (39°F), we recommend not to

use the spa.

• Turn off and unplug the control unit, add some warm water to raise the

spa water temperature above 5°C (41°F), then press the button to

heat up the water to the desired temperature.

• If problem persists, contact Intex Service Center.

E95

• Water temperature is

around 50°C (122°F).

• Turn off and unplug the control unit. When the water has cooled down,

plug the RCD and restart all over again.

• Turn the heater off, then press the ﬁ lter and jet buttons to lower the

water temperature.

• If problem persists, contact Intex Service Center.

E96

• System Error.

• Turn off and unplug the control unit, use the cap to stop the water

from ﬂ owing out of the tub, disassemble and drain out the control unit.

Reassemble the control unit back to the tub. Plug the RCD and restart

all over again.

• If problem persists, contact Intex Service Center.

E97 • Dry-ﬁ re Protection.

• Contact Intex Service Center.

E99

• Water temperature sensor broken.

• Contact Intex Service Center.

END

• After 72 hours of continuous

heating operation, the pump will

hibernate automatically. The

rapid heating and water ﬁ ltration

functions are disabled.

• Press the button to re-active the ﬁ lter pump.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex PureSpa - SJB-HS-30-1C Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex PureSpa - SJB-HS-30-1C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info