Bedienungsanleitung Intex Purespa Jet And Bubble Deluxe SC-20N (Seite 14 von 34) (Englisch)

720173

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

344

NLA

S AVE THESE INSTRUCTIONS

(344NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2019

English

Page 14

SET UP (continued)

Spa Control Unit Installation

1. Connect the spa control unit to the spa tub (see drawing 10). Hand-tighten the connectors securely. Do

not use tools to tighten. Replace the control base side covers (36).

NOTE: Never attach external accessories not supplied with the kit to the spa tub or control base unit, as

this will void the warranty.

CAUTION: Do not sit, lean, cover or place any objects over the spa control unit.

2. Attach the ﬁ lter cartridge housing assembly to the inside of the spa tub outlet grid (see drawing 11).

Inﬂ ate the spa tub ﬁ rst before installing ﬁ lter pump ﬁ ttings.

3. Before ﬁ lling with water ensure the bottom drain valve caps are securely closed on the inside and outside.

4. Fill the spa tub with freshwater to a level between MIN and MAX marked on the inside of the spa wall. Do

not over ﬁ ll the spa. Never move the spa tub with water inside and/or with the control base attached to the

spa as the spa or control base may be damaged.

WARNING: Never pour water with a temperature higher than 40°C (104°F) into the spa

directly. It is recommended to ﬁ ll the spa tub with lukewarm water for quick heating and

energy saving.

5. Place the spa cover and spa air bladder (pre-installed in spa cover) over the spa tub, and make sure the

spa cover buckles are locked using the key provided after pulling the buckled straps tight.

IMPORTANT: Inspect the spa cover regularly for leak, premature wear and tear or deterioration. Never

use a damaged spa cover.

6. Ensure that the spa base is plugged into a properly located and sized electrical outlet and press the

button to turn on the control panel. Press the button on the control panel to activate the heater, see “Spa

Control Panel” operation section.

Spa Cover

The attachment buckles of the cover are locking buckles. Two keys are provided in the plastic bag with the

manual and other accessories. Each buckle is marked with “locked” and “unlocked” symbols for easy operation:

put the key into the slot on the buckle and turn it to the appropriate position to lock or unlock the buckle

respectively.

To assure safety from unauthorized access, always put the cover on when spa is not in use and lock all

buckles. Always keep the keys out of reach of children. In case you misplace the keys, you can use any similar

size ﬂ at screwdriver to lock or unlock the buckles.

When the spa is being used, the cover should be placed in a clean, dry area, otherwise it can pick up dirt and

bacteria. Covers should not be put on wooden tables or wooden decking because of the risk of bleaching the

wood. A cover lifter, dedicated support or similar device, is recommended for ensuring that the cover, mostly its

side facing the water, does not come into contact with the ground or any other dirty surfaces.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Purespa Jet And Bubble Deluxe SC-20N Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex Purespa Jet And Bubble Deluxe SC-20N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info