Bedienungsanleitung Intex Purespa Jet And Bubble Deluxe SC-20N (Seite 17 von 34) (Englisch)

720173

Zoom out

Zoom in

Vorherige Seite

1/34

Nächste Seite

344

NLA

S AVE THESE INSTRUCTIONS

(344NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/09/2019

English

Page 17

SPA CONTROL PANEL

G: Sanitizer Button

H: Heat Button

I: Heater Start Timer (HST) Button

OPERATION (continued)

Sanitizer Button: Use this button to activate and set operating hours for the sanitation

system.

Heat Button: Press this button to activate the heating system. Press or to set the

desired water temperature. The heater will continuously heat until the water temperature

reaches the set temperature and then hold at that temperature. This is achieved by the heater

restarting automatically whenever the water temperature drops 1-2°C (1.8-3.6°F) below the set

temperature. When the ﬂ ame icon on the display is red, the heating system is activated. When

the ﬂ ame icon turns green, the water is at the set temperature. The heating system is then at

rest, but the ﬁ ltration system will continue circulating water nonstop, unless manually turned off.

If the heating system is reactivated, the ﬁ lter pump will restart at the same time.

NOTE: To stop the ﬁ ltration system while the heater is at rest mode, press the ﬂ ame button

ﬁ rst and then the ﬁ lter button. Pressing the heat button only while the heater is at rest mode will

turn off the heating system only and the ﬁ ltration system will operate for 1 more minute before

it turns off or continue with the ﬁ lter pump preset operating hours. To turn the heater off while

heating, press the ﬂ ame button.

IMPORTANT: The following conditions will lead to slow water heating:

• The ambient temperature is lower than 50ºF (10ºC).

• Outdoor wind speed is above 8-12 mph (3.5-5.4 m/s).

• The jet or bubble function is activated when heating the spa water.

• The spa is not properly covered with the spa cover when the water is heating.

Heater Start Timer (HST) Button: Use this button to select a future start time for the heating

system. Press this button and then press or to set the number of hours by which you

wish to delay the start of the heating system, from 000 to 120 hours. The icon will ﬂ ash red for a

few seconds and then stays red. The information shown on the LED display alternates between

the remaining hours before heater start and the water temperature. Once the countdown timer

reaches 000, the heating system will start operating. To deactivate the function at any time,

simply set the HST time back to 000. To readjust the preset hours, press the HST button twice

and adjust the hours with and buttons.

Example 1: It is 9:00pm Monday evening and you would like the spa to be hot on Friday

evening. Allowing for 24 hours for the spa to heat up (4 persons model about 1.5-2.5ºC (3-4.5ºF)

per hour) the heater should be set to start on Thursday evening. With the Spa turned on, ﬁ rst

press the Heat button and set your desired temperature. Press the HST button and then

or until 072 hours is shown. The heater will start after 72 hours has passed (Thursday at

9:00pm) and will run until the desired temperature is attained. The heater will then cycle on

and off to maintain the set temperature until turned off. To turn off the heater, press the ﬂ ame

button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Purespa Jet And Bubble Deluxe SC-20N Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex Purespa Jet And Bubble Deluxe SC-20N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info