Bedienungsanleitung Intex PureSpa SJB-HS-30-1G (Seite 26 von 29) (Englisch)

686582

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

299

NLA

S AVE THESE INSTRUCTIONS

(299NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 05/10/2017

English

Page 26

TROUBLESHOOTING (continued)

PROBLEM CAUSE SOLUTION

TUB HAS A

STRANGE SHAPE

• Expanded internal air pressure by

strong sunshine.

• Do not expose the spa to direct sunlight for

extended period of time.

• Check the air pressure and release air if

necessary. During very hot weather, you must

check to see whether it is necessary to release

some air. This is to avoid any possible damage

to the tub.

TUB LOSES AIR

PRESSURE

• Air valve cap loose.

• Air valve base loose.

• Hole, cut or split on spa tub.

• Ensure air valve cap is securely closed.

• Fill up the spa tub with air then make sure the

air valve base is tighten, see “Spa Tub Air Valve

Fastening” section.

• Put liquid soap and water in a squirt bottle and

spray on seams. If there is a leak it will bubble.

After you ﬁ nd the leak, clean and dry the leaking

area, then apply the repair patch that comes with

your spa.

LEAKING BETWEEN

SPA TUB

CONNECTORS AND

CONTROL UNIT

CONNECTORS

• Spa control base inlet/outlet

connections not securely tight.

• Spa control base inlet/outlet o-ring

missing/dirty.

• Tighten inlet and outlet connections.

• Coat the o-ring with petroleum jelly for water

proof.

• Remove grid from inside spa with a screwdriver,

ensure inlet/outlet O-ring is in place, clean and

not damaged.

SPA IS TOO NOISY

IN FILTRATION

MODE ONLY

• Control base components not

securely attached.

• Control base ground not level and

ﬁ rm.

• Spa ﬁ lter motor failed.

• Ensure control panel, back cover and all

inlet/outlet are securely connected.

• Ensure ground is level, ﬁ rm and smooth.

• Replace the failed ﬁ lter motor with a new one.

INSUFFICIENT

CHLORINE

• Insufﬁ cient operating time of the

sanitation system and/or heater is

running at the same time.

• Chlorine loss due to intense

sunlight exposure.

• The bather load has increased.

• Clogged or dirty electrolytic cell.

• Increase the sanitation system operating time

and ensure the heater is off during the

sanitation process. See “Sanitation System

Operating Instructions”.

• Use a SPA cover when the SPA is not in use

and/or when the sanitation system is operating.

• Increase the sanitation system operating time

and test the water using the test strips. See

“Sanitation System Operating Instructions”.

• Check and clean the cell if necessary. See

“Maintenance”.

BUBBLE AIR

BLOWER DOES NOT

WORK

• Air blower pump is too hot. • Turn off and unplug the spa. Let it cool down and

restart all over again.

• If problem persists contact Intex Service Center.

IMPORTANT

If you continue to experience difﬁ culty, please contact our Consumer Service Department for

assistance. See separate “Authorized Service Centers” sheet.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex PureSpa SJB-HS-30-1G Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex PureSpa SJB-HS-30-1G

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info