Bedienungsanleitung Intex SB-HW10 PureSpa (Seite 22 von 27) (Englisch)

784579

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

346

S AVE THESE INSTRUCTIONS

(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019

English

Page 22

Spa Tub Drainage

1. Turn off the spa control unit.

2. Connect the drain valve adaptor to a garden hose and point the other end

of the garden hose to a suitable draining area (see drawing 14).

3. Remove the drain valve cap from outside of the spa tub and attach the

drain valve adaptor to the drain valve (see drawing 14).

4. From inside of the spa tub, open the drain valve cap, water will start

ﬂ owing out from the garden hose.

5. When the water stops draining, disconnect the spa control unit from

the spa tub wall. Lift the spa tub wall from the side opposite the drain,

leading any remaining water to the drain and emptying the spa completely

(see drawing 15).

6. Attached the inﬂ ation hose (7) to the air blower inﬂ ation outlet on the

control unit.

7. Turn on the spa and press the button, aim the inﬂ ation hose at the

inlet/outlets on the spa tub and spa control unit to dry out any water in the

piping system

(see drawings 16 & 17).

8. Use a clean towel to wipe up any remaining water and moisture on the

spa tub and spa control unit.

9. Ensure the spa tub and spa control unit are thoroughly dried.

NOTE: The enclosed plugs (15) can be used to cover the water inlet and

outlet connectors from the inside of the spa tub to prevent water from

ﬂ owing out.

Spa Tub Cleaning

If dirt is visible in the water or water becomes cloudy and proper water

chemistry does not clear it up, change the water and clean the spa tub.

See “Spa Tub Drainage” section on how to drain the spa.

While empty, remove the cartridge housing from inside of the spa tub wall,

clean and/or replace the ﬁ lter cartridge. Use a sponge and mild soap solution

to wipe away any soil or stains on the inside of the spa wall. Rinse thoroughly

before reﬁ lling with clean water.

IMPORTANT: Do not use steel wool, hard brushes or abrasive cleaners.

Spa Tub Air Valve Fastening

Check the spa tub air valve for leakage and tightness before use. If air is leaking from the air valve, use the

provided wrench (22) to tighten the air valve as follow:

1. Make sure the spa tub is deﬂ ated, open the air valve cap and insert the

wrench

(22) into the air valve body (see drawing 18).

2. With one hand, hold the backside of the air valve base from the inside of

the spa tub wall and turn the wrench (22) clockwise.

IMPORTANT: Never adjust the air valve base when the spa is in use or

ﬁ lled with water. Only use the air valve wrench if the air valve is loose or

there is leakage around air valve base. Do not over tighten the air valve:

over tightening can damage the valve. Just ensure the air valve is snug

and not leaking.

MAINTENANCE

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex SB-HW10 PureSpa Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info