686594
1
Zoom out
Zoom in
Vorherige Seite
1/23
Nächste Seite
342
GS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Model SF80220RC-2
220-240 V~, 50 HZ, 250 W, Hmax 5 m Hmin 0.19 m IPX4
Model SF70220RC-2
220-240 V~, 50 HZ, 450 W, Hmax 7.5 m Hmin 0.19 m IPX4
Model SF60220RC-2
220-240 V~, 50 HZ, 550 W, Hmax 7.5 m Hmin 0.19 m IPX4
MAX. WATER TEMPERATURE 35°C
IMPORTANT
SAFETY RULES
Please read, understand, and follow all
instructions carefully before installing
and using this product. Keep for future
reference.
Don’t forget to try these other fine Intex products: pools, pool
accessories, inflatable pools and in-home toys, airbeds and boats
available at fine retailers or visit our website.
Due to a policy of continuous product improvement, Intex reserves
the right to change specifications and appearance, which may
result in updates to the instruction manual without notice.
©2019 Intex Marketing Ltd. - Intex Development Co. Ltd. - Intex Recreation Corp.
All rights reserved/Tous droits réservés/Todos los derechos reservados/Alle
Rechte vorbehalten. Printed in China/Imprimé en Chine/Impreso en China/Gedruckt
in China.
®™ Trademarks used in some countries of the world under license from/®™ Marques utilisées dans certains pays sous
licence de/Marcas registradas utilizadas en algunos países del mundo bajo licencia de/Warenzeichen verwendet in einigen
Ländern der Welt in Lizenz von/Intex Marketing Ltd. to/à/a/an Intex Development Co. Ltd., G.P.O Box 28829, Hong
Kong & Intex Recreation Corp., P.O. Box 1440, Long Beach, CA 90801 • Distributed in the European Union by/Distribué
dans l’Union Européenne par/Distribuido en la unión Europea por/Vertrieb in der Europäischen Union durch/Intex Trading
B.V., Venneveld 9, 4705 RR Roosendaal – The Netherlands
www.intexcorp.com
For illustrative purposes only.
OWNER’S MANUAL
342-*GS-R0-2008
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 2
Warnings.......................................................................... 3
Parts References............................................................. 4-5
Setup Instructions ......................................................... 6-13
Product Specifications................................................... 8
Operating Instructions ................................................... 14-16
Intex Pools Operating Time Table.................................. 17
Non-Intex Pools Operating Time Table..........................
18
Maintenance.................................................................... 19
Long Term Storage.......................................................... 20
Troubleshooting Guide................................................... 21
Common Pool Problems................................................. 22
General Aquatic Safety................................................... 22
Limited Warranty............................................................. 23
TABLE OF CONTENTS
RCD OPERATING INSTRUCTIONS
Plug RCD into power outlet. Press RESET button on the RCD plug.
Indicator should be "ON".
Press TEST button on the RCD plug. Indicator should be "OFF".
Press RESET button for use. Do not use if test fails. Contact a qualified
electrician to determine cause of failure.
RESET
RESET
TEST
TEST RESET
RESET
RESET
TEST
TEST
TEST
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 3
IMPORTANT SAFETY RULES
Read, Understand and Follow All Instructions Carefully Before Installing and Using this Product.
READ AND FOLLOW ALL INSTRUCTIONS
WARNING
Always supervise children and those with disabilities.
Children must stay away from this product and electrical cord(s).
• Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without
supervision.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved.
Assembly and disassembly by adults only. Cleaning and user maintenance must be performed by an adult above 18
years old who is familiar with the risk of electric shock.
Risk of electric shock. Connect this product only to a grounding type receptacle protected by a ground-fault circuit
interrupter (GFCI) or residual current device (RCD). Contact a qualified electrician if you cannot verify that the
receptacle is protected by a GFCI/RCD. Use a qualified electrician to install the GFCI/RCD, which has a maximum
rate of 30mA.
Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to
the product.
• Always unplug the appliance on raining days or if leave it for long time (such as going out for holidays).
• The plug must be accessible after produc t is installed.
Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and
other equipment.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons
in order to avoid a hazard.
To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or converter plugs to connect
unit to electric supply; provide a properly located outlet.
Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
Keep this product more than 3.5m away from the pool.
Keep the plug of this product more than 4m away from the pool and at a height of 1.2m at least.
Position this product away from the pool, so as to prevent children from climbing on it and accessing the pool.
Do not operate this product when pool is occupied.
This product is for use with storable pools only. Do not use with permanently installed pools. A storable pool is
constructed so that it may be readily disassembled for storage and reassembled to its original configuration.
To reduce the risk of entrapment hazard, never enter the pool if suction strainer component is loose, broken, cracked,
damaged or missing. Replace loose, broken, damaged, cracked or missing suction strainer components immediately.
Never play or swim near suction fittings. Your body or hair may be trapped causing permanent injury or drowning.
To prevent equipment damage and risk of injury, always turn pump off before changing the filter control valve position.
Never operate this product above the maximum working pressure stated on the filter tank.
Hazardous Pressure. Improper tank valve cover assembly could cause the valve cover to blow off and cause serious
injury, property damage or death.
This product is intended to be used only for the purposes described in the manual!
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN PROPERTY DAMAGE, ELECTRIC SHOCK,
ENTANGLEMENT OR OTHER SERIOUS INJURY OR DEATH.
These product warnings, instructions and safety rules provided with the product represent some common risks of water
recreation devices and do not cover all instances of risk and danger. Please use common sense and good judgement
when enjoying any water activity.
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 4
PARTS REFERENCE
Before assembling your product, please take a few minutes to check the contents
and become familiar with all the parts.
NOTE: Drawings for illustration purpose only. Actual product may vary. Not to scale.
" * ": These parts are not included if this pump was not purchased as part of a pool set. Contact
our Authorized Service Centers to order these parts if needed.
1
5
9
11
2
13
35
20
32
33 34 19
3
6
7
4
12
15
16
17
18
8
10
14
3637
38
19
20
39
21
23 24 25 27
22
23 28 30
21
23 28
21
22
29 31
*
**
23 24
21
22
25 26
*40
22
41
44
42
41
43
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 5
REF. NO. DESCRIPTION QTY. SPARE PART NO.
SF80220RC-2 SF70220RC-2 SF60220RC-2
1 PRESSURE GAUGE 1 11411 11224 11224
2 6-WAY VALVE 1 11378 11496 11496
3 DRAIN OUTLET COVER 1 11131 11131 11131
4 CLAMP 1 11380 11380 11380
5 TANK O-RING 1 11379 11379 11379
6 SAND SHIELD 1 11382 11382 11382
7 CENTER PIPE HUB 1 11815 11813 11814
8 LATERAL 10 11484 --
12 - 11384 11384
9 DRAIN VALVE CAP 1 11456 11456 11456
10 DRAIN VALVE O-RING 1 11385 11385 11385
11 L-SHAPE O-RING 4 11228 11228 11228
12 HOSE WITH NUTS 2 11010 11010 11010
13 SAND FILTER INTERCONNECTING HOSE 1 11820 11388 11535
14 LEAF TRAP NUT 1 11822 11479 11479
15 LEAF TRAP O-RING 1 11824 11232 11232
16 BASKET 1 11821 11260 11260
17 FILTER HOUSING NUT 1 11261 11261 11261
18 L-SHAPE O-RING 1 11412 11412 11412
19
AIR RELEASE VALVE/SEDIMENT RELEASE VALVE
2 10460 10460 10460
20 VALVE O-RING 2 10264 10264 10264
21*
PLUNGER VALVE (HOSE O-RING & STEP WASHER INCLUDED)
2 10747 10747 10747
22* HOSE O-RING 2 10262 10262 10262
23* STEP WASHER 2 10745 10745 10745
24* STRAINER NUT 2 10256 10256 10256
25* FLAT STRAINER RUBBER WASHER 2 10255 10255 10255
26* THREADED STRAINER CONNECTOR 1 10744 10744 10744
27* ADJUSTABLE POOL INLET JET NOZZLE 1 12369 12369 12369
28* ADAPTOR B 2 10722 10722 10722
29* STRAINER CONNECTOR 1 11070 11070 11070
30* POOL INLET JET NOZZLE 1 12364 12364 12364
31* STRAINER GRID 112197 12197 12197
32 SCREW 2 11381 11381 11381
33 PUMP MOTOR & CONTROL 112706GS 12708GS 12710GS
34 PRE-FILTER ASSEMBLY 1 11826 11371 11371
35 LEAF TRAP COVER 1 11823 11480 11480
36 SAND FILTER PUMP MOTOR INLET O-RING 2 11457 11457 11457
37 SAND FILTER PUMP TANK 1 12712 12713 12714
38 SAND FILTER PUMP TANK BASE 1 12716 12717 12718
39 PRE-FILTER HOUSING 1 12100 12099 12099
40* STRAINER GRID 1 12198 12198 12198
41* AIR JET VALVE 1 12363 12363 12363
42* INLET THREADED AIR CONNECTOR 1 12371 12372 12372
43* POOL INLET AIR ADAPTOR 1 12368 12368 12368
44* INLET STRAINER CONNECTOR 1 12365 12365 12365
45* AIR JET VALVE CAP (NOT SHOWN) 1 12373 12373 12373
" * ": These parts are not included if this pump was not purchased as part of a pool set. Contact our
Authorized Service Centers to order these parts if needed.
When ordering parts, be sure to quote the model number and part numbers.
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 6
The strainer grid prevents large objects from jamming and/or damaging the filter pump. If
your pool has an inflatable top ring, install the strainer, nozzle and plunger valve before
inflating the pool liner top ring. The part numbers here onward refer to the parts depicted
in the Parts List section of this manual. To install, do the following:
1. In a counter-clockwise motion unscrew
plunger valve union from the threaded
strainer connector
(26) (see drawing 1).
Be careful not to lose the step rubber
washer
(23). Place the plunger valve on
the ground in a safe place.
2. In a counter-clockwise motion unscrew the
strainer nut
(24) from the threaded
connector
(26). Leave the flat washer (25)
on the connector (26).
3. Install the strainer and plunger valve at the
lower position of pool outlet (marked "+").
From the inside of the pool liner insert the
connector
(26) into one of the pre-cut holes
with the washer remaining on the connector
to be placed against the inside of the liner
wall.
4. Before assembly, lubricate the threads with
a petroleum jelly. With the flat side of the
strainer nut
(24) facing the outside wall of
the liner in a clockwise motion screw the
strainer nut
(24) back onto the threaded
connector
(26) (see drawing 2).
5. Finger tighten the strainer nut (24) onto the
threaded connector
(26).
6. Grasp the plunger valve assembly. Make
sure the step washer (23) is in place.
7. In a clockwise motion screw the plunger
valve union back onto the threaded
connector
(26) (see drawing 3).
8. In a clockwise motion turn the plunger
valve handle to close position. Ensure the
plunger valve is securely closed. This will
prevent water from flowing out during filling
of the pool (see drawing 4).
POOL OUTLET - STRAINER & PLUNGER VALVE SETUP (optional)
2
25 26
INSIDE
LINER WALL
24
1
23
2
1
3
1
2
4
INSIDE
LINER WALL
40
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 7
POOL INLET - NOZZLE & PLUNGER VALVE SETUP (optional)
5
2
1
7
1
2
8
INSIDE
LINER WALL
9
WATER
FLOW
POOL
6
25 42 27
INSIDE LINER
WALL
24
41
1. In a counter-clockwise motion unscrew plunger valve
union from the inlet threaded air connector (42) (see
drawing 5). Be careful not to lose the step rubber
washer
(23). Place the plunger valve on the ground in
a safe place.
2. In a counter-clockwise motion unscrew the strainer
nut
(24) from the inlet threaded air connector (42).
Leave the flat washer (25) on the connector (42).
3. Install the nozzle and plunger valve at the upper
position of pool inlet. From the inside of the pool liner
insert the nozzle union (27 & 42) into one of the
pre-cut holes with the washer remaining on the
connector to be placed against the inside of the liner
wall.
4. Before assembly, lubricate the threads with a
petroleum jelly. Then, with the flat side of the
strainer nut
(24) facing the outside wall of the liner
in a clockwise motion screw the strainer nut (24)
back onto the inlet threaded air connector (42) (see
drawing 6).
5. Finger tighten the adjustable pool inlet jet nozzle (27)
and the strainer nut (24) onto the inlet threaded air
connector (42).
6. Grasp the plunger valve assembly. Make sure the
step washer
(23) is in place.
7. Screw the air jet valve (41) over the inlet threaded air
connector
(42). NOTE: Make sure the air jet valve
is securely tighten and facing up. In a clockwise
motion screw the plunger valve union back onto the
inlet threaded air connector (42) (see drawing 7).
8. In a clockwise motion turn the plunger valve handle
to close position. Ensure the plunger valve is securely
closed. This will prevent water from flowing out during
filling of the pool (see drawing 8).
9. Adjust the direction of nozzle head pointing away
from the pool outlet for a better circulation result
(see drawing 9).
10. The pool liner is now ready to fill with water. Consult
the above-ground-pool owner’s manual for filling
instructions.
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 8
PRODUCT SPECIFICATIONS
SETUP INSTRUCTIONS
The sand filter removes suspended particles but does not sanitize your pool. Pool chemistry
is a specialized area and you should consult your local pool service specialist for details
.
TOOLS REQUIRED: One (1) Phillips screwdriver
Pump location and mounting:
The system must be installed on a solid level and vibration-free base.
Provide a location protected from the weather, moisture, flooding and freezing
temperature.
Provide adequate access, space and lighting for routine maintenance.
Pump motor requires free circulation of air for cooling. Do not install the pump in a
damp or non-ventilated location.
A team of 2 or more people is recommended for setting up this product.
The appliance is intended only for household use.
Motor pre-filtering assembly setup:
1. Remove the sand filter and its accessories from the packaging carefully and inspect for any
visible damage.
2. In a counter-clockwise motion unscrew the leaf trap cover (35) from the pre-filter housing.
Take out the basket (16) and filter housing nut (17) (see drawing 10).
3. Connect the pre-filter housing to the motor water inlet. Note: Align the connector in the
pre-filter housing with the water inlet on the motor (see drawing 11).
11
10
35
17
16
14
Model: SF80220RC-2 SF70220RC-2 SF60220RC-2
Power: 220-240 Volt AC 220-240 Volt AC 220-240 Volt AC
Wattage: 250 W 450 W 550 W
Maximum working pressure:
2 bar (30 psi) 2 bar (30 psi) 2 bar (30 psi)
Effective filtering area: 0.07 m2 (0.79 ft2) 0.1 m2 (1.07 ft2) 0.13 m2 (1.44 ft2)
Pump flow rate (at pump
outlet): 7.9 m3/h (2100 GPH) 10.5 m3/h (2800 GPH) 12 m3/h (3200 GPH)
Recommended filtering
media quantity:
No. 20 silica sand
23 Kg (50 Lbs) or glass
sand 16 Kg (35 Lbs).
No. 20 silica sand
35 Kg (77 Lbs) or glass
sand 25 Kg (55 Lbs).
No. 20 silica sand
55 Kg (120 Lbs) or glass
sand 38 Kg (85 Lbs).
Recommended filtering
media (Not included): No. 20 silica sand or glass sand. Particle size range 0.45 to 0.85
mm (0.018 to 0.033 inches). Uniformity Coefficient less than 1.75.
Limited Warranty: see “Limited Warranty”
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 9
4. In a clockwise motion screw filter housing nut (17) onto the motor water inlet (see
drawings 12.1 & 12.2).
5. Replace the basket (16) and leaf trap cover (35) back to the pre-filter housing (see
drawings 13.1 & 13.2).
SETUP INSTRUCTIONS (continued)
Sand tank installation:
1. Place the tank support base at the selected location.
2. Place the tank on the tank support base (see drawing 14.1).
3. Connect the motor pre-filtering assembly unit to the tank support base (see drawing 14.2).
NOTE: Ensure the pre-filter housing water inlet hose connection is facing towards the pool.
IMPORTANT: Some countries, especially in the European community, require the
product to be secured to the ground or to a base in a permanent upright position.
Check your local authorities to determine if there is a regulation in your area
regarding above-the-ground swimming pool filter-pumps. If yes, then the product
can be mounted to a platform using the two holes located in the base.
See drawing 14.3.
The product can be mounted on a cement base or onto a wooden platform to
prevent accidental falling over.
The mounting holes are 6.4 mm in diameter and spaced 210 mm for model
SF80220RC-2 (spaced 224 mm for model SF70220RC-2 & SF60220RC-2) apart.
Use two bolts and lock nuts with a maximum of 6.4 mm in diameter.
13.1 13.2
12.1
17
12.2
17
14
16
35
19
14.1 14.2 14.3
Model SF80220RC-2: 210 mm
Model SF70220RC-2 & 60220RC-2: 224 mm
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 10
SETUP INSTRUCTIONS (continued)
Sand loading:
IMPORTANT: Use No. 20 silica sand or glass sand with particle size range 0.45 to 0.85 mm
(0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75.
Only use the filter media specified by the manufacturer.
NOTE: Before loading the tank with sand, ensure the center pipe hub assembly is
securely in place at the bottom of the tank, and vertically centered inside the tank.
1. Place the sand shield (6) over the top of the center pipe. Pour the sand into the tank at
a slow rate (see drawing 15).
2. Fill the tank approximately half way, remove the sand shield (6) from the top (see
drawing 16).
3. Evenly distribute the sand inside the tank, then fill the tank with some water to provide a
cushioning effect when the remaining sand is poured in. This prevents the center pipe
hub
(7) from excessive shock (see drawing 17). Place the sand shield (6) back and
continue to pour the sand into the tank.
4. Sand shall be filled between the “MAX” and “MIN” marked gauge on the center pipe (see
drawings18).
5. Remove the sand shield (6) (see drawing 16) and evenly spread and level out the sand by
hand
(see drawing 17).
6. Wash away all sand around the top edge of the tank.
15
6
16
6
MAX
MIN
17
7
MAX
MAX
MIN
MIN
MAX
MIN
18
7
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 11
6-way valve installation:
1. Lower the 6-way valve over the tank slowly, and ensure the bypass pipe protruding
underneath the 6-way valve fits securely into the center pipe hub (7) top opening
(see drawing 19).
IMPORTANT: There are three hose connection ports on the 6-way valve, ensure the outlet
connection (from filter to the pool) on the valve is facing towards the pool, and the inlet
connection (from motor to valve) is aligned with the motor outlet (see drawing 20).
SETUP INSTRUCTIONS (continued)
WARNING
Improper tank valve and clamp assembly could cause the valve and
clamp to blow off and cause serious injury, property damage or death.
2. Place an L-shape o-ring (11) on the 6-way valve inlet connection and on the pump motor
outlet. In a clockwise motion connect the sand filter interconnecting hose (13) between
the pump motor outlet and the 6-way valve inlet connection (see drawing 21).
3. Remove the clamp bolt, and install the clamp around the tank and 6-way valve flanges,
then replace the clamp bolt and use a phillips screwdriver (not included) to tighten it
(see drawing 22).
20
WATER
INLET
WATER
OUTLET
19
7
21
13
22
4
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 12
SAND FILTER PUMP HOSE CONNECTION SETUP
The 6-way valve has three hose connection ports.
1. Connect one hose (12) end to the pre-filter inlet and the other end of the hose to the lower
plunger valve with the strainer. Ensure the hose nuts are securely tightened.
2. Connect the second hose (12) between the 6-way valve water outlet and the upper plunger
valve with the inlet-nozzle. Ensure the hose nuts are securely tighten.
3. The third hose connection port (drain/waste outlet) on the 6-way valve shall be directed to
a proper draining receptacle using a hose or pipe (not provided). Remove the drain cap
before attaching the drain/waste hose or pipe.
4. The sand filter pump is now ready to filter the pool.
WARNING
Keep this product more than 3.5m away from the pool.
Keep the plug of this product more than 4m away from the pool and at a
height of 1.2m at least.
Position this product away from the pool, so as to prevent children from
climbing on it and accessing the pool.
(ILLUSTRATION NOT TO SCALE)
According to the International Standard, IEC 60364-7-702, on electrical installation of swimming
pools and other basins equipment, the following installation distances must be respected:
The filter pump must be positioned more than 3.5m away from the pool walls.
The power cord plug to the 220-240 volt electrical power source of the filter pump must
be positioned more than 4m away from the pool walls.
Check your local authorities to determine the appropriate standard and requirements for
“electrical installation of swimming pools and basins equipment”. The following table is for
reference only:
International
France
Germany
The Netherlands
Country/Region Standard Number
IEC 60364-7-702
NF C 15-100-7-702
DIN VDE 0100-702
NEN 1010-702
>3.5M
6-WAY VALVE
WATER
INLET
WATER
OUTLET
MOTOR
MOTOR
WATER
OUTLET
PRE-
FILTER
WATER INLET
WATER LEVEL
ADJUSTABLE
POOL INLET
JET NOZZLE
THREADED
STRAINER
CONNECTOR
OUTSIDE
LINER WALL
PLUNGER
VALVE
POWER
CORD
RCD
L-SHAPE
O-RING
L-SHAPE
O-RING
TO
DRAIN
AIR RELEASE VALVE
AIR JET VALVE
INLET THREADED AIR
CONNECTOR
>4M
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 13
SAND FILTER PUMP HOSE CONNECTION SETUP (continued)
For INTEX pool with 1-1/4” (32mm) connections/hoses:
Make sure the air jet valve (41) is securely tighten onto the pool inlet air adaptor (43) and facing
up.
For NON-INTEX pool:
Connect the hose (12) to the pool inlet/outlet connection with a large hose clamp. Tighten
securely.
POOL
LARGE HOSE
CLAMP
12
3
44
28
(Adaptor B) 43 41 30 29 31
23 28
(Adaptor B)
23
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 14
OPERATING INSTRUCTIONS
Valve Position Function Water Flow Direction
FILTER
(see drawing 23) Normal filtration and regular vacuuming
of pool From pump through filter media to
pool
BACKWASH
(see drawing 24) Reverses water flow to clean filter
media From pump through filter media to
valve waste/drain outlet
RINSE
(see drawing 25)
For initial startup cleaning of the sand, and
leveling the sand bed after backwashing
From pump through filter media to
valve waste/drain outlet
WASTE
(see drawing 26) For vacuuming directly to waste,
lowering pool level or to drain the pool From pump to valve waste/drain
outlet bypassing the filter media
RECIRCULATE
(see drawing 27) For circulating water back to pool
without going through the filter media From pump through valve to pool
bypassing the filter media
CLOSED
(see drawing 28)
Shuts off all flow to filter and pool “Do not
use this setting with pump running”
6-way valve positions and function:
Risk of electric shock. Connect this product only to a grounding type receptacle protected
by a ground-fault circuit interrupter (GFCI) or residual current device (RCD). Contact a
qualified electrician if you cannot verify that the receptacle is protected by a GFCI/RCD.
Use a qualified electrician to install the GFCI/RCD, which has a maximum rate of 30mA.
To reduce the risk of electric shock, do not use extension cords, timers, plug adaptors or
converter plugs to connect unit to electric supply; provide a properly located outlet.
Do not attempt to plug in or unplug this product while standing in water or when your
hands are wet.
Never operate this product above the maximum working pressure stated on the filter tank.
Always switch off pump before changing the 6-way valve position.
Operating this product without water flowing through the system can cause a build up of
hazardous pressure which can result in an explosive situation, serious injury, property
damage or death.
Never test this pump with compressed air. Never operate the system with water
temperature above 35°C (95°F).
WARNING
RE
T
L
I
F
E
S
N
I
R
ET
A
L
U
C
RI
C
E
R
E
S
O
LC
ETSA
W
B
23
E
SN
IR
ETALU
C
RICER
HSAW
K
C
A
B
E
S
O
LC
E
TSAW
24
RE
TL
I
F
ES
N
IR
E
TALU
C
RICER
H
SAWKCAB
ETSA
W
25
R
E
T
LI
F
E
S
NI
R
ER
H
S
AWK
CA
B
E
SO
L
C
ETSAW
26
R
E
T
LIF
ESN
I
R
E
TA
L
U
C
R
I
CE
R
H
S
A
W
K
C
A
B
E
S
O
L
C
27
R
E
TLI
F
ETALUC
R
ICER
H
S
AWK
CA
B
ES
O
LC
ETSAW
28
Control panel description:
ON / OFF button LOCK / UNLOCK button TIMER button
LED Reading Definition
00 Stand-by mode (start-up / operating cycle finished)
01 Minimum operating hour (1 hour remaining)
02-11 Operating hours (2 - 11 hours remaining)
12 Maximum operating hours (12 hours remaining)
FP Timer OFF (pump operating continuously)
Power saving mode
.
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 15
Initial startup and operation:
Before operating, be sure that:
All the hoses have been connected and tightened securely, and correct amount of filter sand
have been loaded.
The entire system is connected to a grounding type receptacle protected by a ground-fault
circuit interrupter (GFCI) or residual current device (RCD).
OPERATING INSTRUCTIONS (continued)
CAUTION
The filter control valve has a closed position. The pump should never
be on when the valve is in the closed position. If the pump is operated
with the valve closed, explosive situation could exist.
1. Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valves to
allow water to flow into the sand filter pump. With water flowing into sand filter pump, the water
pressure will allow the air trapped inside to escape from the air release valves (19). When all the
air has escaped water will flow out of the valves (19). When this occurs gently finger tighten the
valves (19) in a clockwise direction.
IMPORTANT: To prevent air lock, open the lower plunger valve (connected inlet hose) first
and then the upper plunger valve (connected outlet hose). Open the air release valves, wait
until water starts to flow out of the air release valves, close air release valves.
2. Ensure the drain/waste outlet on the 6-way valve is not covered and directed to a proper draining
receptacle.
3. BACKWASH - Ensure the pump is off, depress the 6-way valve
and turn it to the “BACKWASH” position (see drawings 24 & 29).
IMPORTANT: To prevent damage to the 6-way valve, always
depress the valve handle before turning. Always switch off
pump before changing the 6-way valve position.
4. Press to switch on the system, and then press to set
the operating TIMER hours (see “Operating the system under
TIMER mode or manually” section for details). Water is circulating
backward through the sand media and to waste/drain outlet.
Backwash until a clear flow of water is observed in the waste/
drain outlet or through the drain sediment window.
NOTE: If the LED display flashes “00”, the device is in stand-by mode and the pump will not
operate. The initial backwash of the filter is recommended to remove any impurities or fine sand
particles in the sand media.
5. Switch off the pump, change the 6-way valve to “RINSE” position (see drawing 25).
6. Switch on the pump and run the pump for about one minute to level out the sand bed after
backwashing the sand media.
7. Switch off the pump, change the 6-way valve to “FILTER” position (see drawing 23).
8. Switch on the pump. The system is now operating in the normal filtering mode. Run the pump
until the desired pool water clearance is obtained and no more than 12 hours per day. For the
initial startup, it is recommended setting the system to a longer TIMER operating hours or “FP” for
the pump to operate continuously without the TIMER.
9. Record the initial pressure gauge reading when the filter media is clean.
NOTE: During initial setup of the system, it may be necessary to backwash frequently due to
unusual heavy dirt present in the water and sand. After that, as the filter removes dirt and
impurities from the pool water, the accumulated dirt in the sand media will cause the pressure
to rise and the flow to diminish. If there is no vacuuming device attached to the system and
the pressure gauge reading is in the yellow zone it is time to backwash the sand media, see
“BACKWASH” under “initial startup and operation” section.
Vacuuming device (i.e. Intex auto pool cleaner) attached to the system may also cause the
flow to diminish and the pressure to rise. Remove any vacuuming device from the system and
check if the pressure gauge reading has dropped from the yellow zone to the green zone.
10. Monitor the pressure gauge reading, and check that the inlet and outlet openings are not
obstructed on a weekly basis. If the pressure gauge indicates yellow it is time to backwash the
filter media.
29
1
2
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 16
OPERATING INSTRUCTIONS (continued)
Operating the system under “TIMER” mode or manually:
To operate the sand filter pump in “FILTER” mode under “TIMER” control:
1. Activate the unit:
Press button. Flashing code “00” appears on the LED display, indicating
that the unit is ready to be programmed.
2. Set operating hours:
With code “00” flashing, press button to set the desired operating
hours. See the “Operating Time Table” for the required operating
hours related to each pool size. Pressing will increase the time
from 01 to 12 hours maximum. If you have selected too many hours
keep pressing to repeat the cycle. The built-in timer will now
activate the Sand filter pump, at the same time each day, for the
number of hours you have set.
3. Lock keypad controls:
With the desired hour value showing, press button until you hear a “beep”. Locking the
control buttons into this setting prevents unauthorized changing of the operating cycle.
NOTE: If you forget to lock the keypad controls, the system will automatically lock it and start
working 10 seconds later.
The sand filter pump is now filtering the water and will stop after the operating hours are
completed.
4. Readjust operating time if necessary:
The operating hours can be re-adjusted if necessary. Press button until you hear a “beep”
to unlock the keypad and the current programmed time will flash. Repeat steps 2 to 3.
5. Stand-by/power saving mode:
When the cycle ends, the LED display shows “00”. The system is
now in Stand-By mode. After 5 minutes the system goes into Power
Saving mode and the LED display shows “.”. The system will
automatically turn itself back on in 24 hours.
While the system is in Power Saving mode, press any button and the
system will briefly display the programmed time and then “00”.
To view the TIMER preset hours:
While the pump is operating, press button, the display will briefly flash the preset hours for
10 seconds and then display back the remaining operating hours.
To operate the sand filter pump manually (without the “TIMER” mode):
1. To run the pump alone without the “Timer”, press button to turn
on the pump, then press button until the LED displays “FP”, this
indicates that the TIMER is off and the pump is now operating continuously.
2. To stop the pump, press button again.
(1 to 12 hours max per cycle)
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 17
INTEX POOLS OPERATING TIME TABLE (WITHOUT INTEX SALTWATER SYSTEM)
This table shows the required operating time for average use of the sand filter pump with above
ground pools.
If the system is attached to an “Intex Saltwater System” unit, the filter pump running time
should be longer than the required operating time of the Intex Saltwater System unit.
Pool Size
Water Capacity (Calculated at
90% for Frame Pool and 80% for
Easy Set & Oval Pool)
Sand filter pump operating
time (For one cycle) /
(Hours)
(Gals) (Liters)
SF80220RC-2 SF70220RC-2 SF60220RC-2
INTEX ABOVE GROUND POOLS (AGP’s)
EASY SET®
POOL
457cmx84cm (15'x33") 2587 9792 2 - -
457cmx91cm (15'x36") 2822 10681 2 - -
457cmx107cm (15'x42") 3284 12430 2 - -
457cmx122cm (15'x48") 3736 14141 3 - -
488cmx107cm (16'x42") 3754 14209 3--
488cmx122cm (16'x48") 4273 16173 3 - -
488cmx132cm (16'x52") 4614 17464 3--
549cmx107cm (18'x42") 4786 18115 3 3 2
549cmx122cm (18'x48") 5455 20647 4 3 3
ROUND
METAL
FRAME POOL
457cmx91cm (15'x36") 3282 12422 2 - -
457cmx107cm (15'x42") 3861 14614 3--
457cmx122cm (15'x48") 4440 16805 3--
488cmx122cm (16'x48") 5061 19156 4 - -
549cmx122cm (18'x48") 6423 24311 5 3 3
640cmx132cm (21'x52") 9533 36082 6 5 4
732cmx132cm (24'x52") 12481 47241 8 6 6
ULTRA FRAME
POOL
488cmx122cm (16'x48") 5061 19156 4 - -
549cmx122cm (18'x48") 6423 24311 5 3 3
549cmx132cm (18'x52") 6981 26423 543
610cmx122cm (20'x48") 7947 30079 544
671cmx132cm (22'x52") 10472 39637 7 5 5
732cmx132cm (24'x52") 12481 47241 8 6 6
792cmx132cm (26'x52") 14667 55515 10 7 7
GRAPHITE GRAY
PANEL POOL
SET™
478cmx124cm (15'8"x49") 4440 16805 3--
508cmx124cm (16'8"x49") 5061 19156 4 3 3
569cmx135cm (18'8"x53") 6981 26423 5 4 3
OVAL FRAME
POOL
305cmx549cmx107cm (10'x18'x42")
2885 10920 2 - -
366cmx610cmx122cm (12'x20'x48")
4393 16628 3 2 2
RECT. ULTRA
FRAME POOL
274cmx457cmx122cm (9'x15'x48")
3484 13187 3 2 2
274cmx549cmx132cm (9'x18'x52")
4545 17203 332
305cmx610cmx132cm (10'x20'x52")
5835 22085 4 3 3
366cmx732cmx132cm (12'x24'x52")
8403 31805 6 4 4
488cmx975cmx132cm (16'x32'x52")
14364 54368 976
NOTE: The timer setting has an additional 10 minutes over the actual setting.
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 18
NON-INTEX POOLS OPERATING TIME TABLE
Water Capacity
Sand filter pump operating time (For one cycle) / (Hours)
(Gals) (Liters) SF80220RC-2 SF70220RC-2 SF60220RC-2
3000 11355 2 - -
4000 15140 3 2 2
4440 16805 3 3 2
5000 18925 4 3 3
6000 22710 4 3 3
7000 26495 5 4 3
8000 30280 544
9000 34065 6 5 4
10000 37850 7 5 5
11000 41635 7 6 5
12000 45420 8 6 5
13000 49205 9 7 6
14000 52990 9 7 6
15000 56775 10 7 7
16000 60560 10 8 7
17000 64345 11 8 7
18000 68130 12 9 8
19000 71915 12 9 8
20000 75700 - 10 9
21000 79485 - 10 9
22000 83270 - 11 9
23000 87055 - 11 10
24000 90840 - 12 10
25000 94625 - 12 11
26000 98410 - 12 11
This table shows the required operating time for average use of the sand filter pump with above
ground pools.
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 19
MOTOR PRE-FILTER CLEANING AND MAINTENANCE
It is essential to change any damaged element or set of elements as soon as possible.
Use only parts approved by the manufacturer.
1. Make sure the filter pump is switched off, then disconnect the power cord from the electrical
outlet.
2. Turn both plunger valve handles fully clockwise until they stop. This closes the valve, prevents
the water from flowing out of the pool.
3. Release the pressure first by opening the sediment
release valve (19) located on the lower side of the
pre-filter housing (see drawing 30).
4. In a counter-clockwise motion unscrew the leaf trap
cover (35), then remove the basket (16) and leaf trap
o-ring (15) from the pre-filter housing (see drawing 31).
5. Empty and flush the basket using a garden hose, may use a plastic brush to remove deposits
from the basket. Do not use metal brush.
6. Clean and rinse the inside of the pre-filter housing and the leaf trap O-ring with a garden
hose.
7. Reinstall the leaf trap O-ring, basket and leaf trap cover to the pre-filter housing.
8. Close the sediment release valve (19).
All filter and filter media shall be inspected regularly to ensure that there is no build-up
of debris thus preventing a good filtration. Disposal of any used filter media should be in
accordance with applicable local regulation and legislation.
1
2
30
31
19
14
15
16
35
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 20
1. Before emptying your pool for long term storage, or relocation, be sure the water is directed towards
an acceptable drain water receptacle away from the house. Check local regulations for specific
directions regarding disposal of swimming pool water.
2. Switch off the unit, and disconnect power cord from electrical outlet.
3. When the pool is empty, disconnect all hoses from pump and plunger valves and remove the strainers/
plunger valves from the pool wall.
4. In a counter clockwise motion unscrew the drain valve cap (9) from the drain valve to thoroughly drain
the tank. The drain valve is located at the bottom of the filter tank.
5. Disassemble the pump motor from the tank base.
6. Leave sand filter pump pieces and hoses outside to thoroughly air dry.
7. Coat the following o-rings and washers with petroleum jelly for long term storage:
L-shape o-ring
(11 & 18).
Pump hose O-rings (22).
Strainer valve assembly step washers (23).
Flat strainer rubber washers (25).
8. Depress the 6-way valve handle and rotate so as to set the pointer on the valve top “N” position. This
allows the water to drain from the valve. Leave the 6-way valve in this inactive position.
9. It is best to place all dry pieces and pump motor in the original packaging for storage. To avoid
condensation or corrosion problem, do not cover or wrap pump motor with plastic bags.
10. Store the pump motor and accessories in a dry place. The storage's temperature should be controlled,
between 0 degrees Celsius (32 degrees Fahrenheit) and 40 degrees Celsius (104 degrees Fahrenheit).
11. Cover the tank with a tarpaulin or plastic sheet to protect it from the weather.
POOL CARE & CHEMICALS
All pools require care to keep the water clear and hygienically clean. With proper chemical control, your
filter will help attain this objective. Consult your pool supply dealer for instructions regarding the proper
use of chlorine, algaecide and other chemical agents required for sparkling clear water.
Keep pool chemicals away from children.
Do not replenish chemicals in pool while pool is occupied. Skin or eye irritations could occur.
Daily pH checking and chemical treatment of the water is very important and cannot be
overemphasized. Chlorine, algaecide and maintenance of proper pH levels are required when filling the
pool as well as during the season. Consult your local swimming pool supply store for instructions.
The season's first filling of the pool may have brackish water requiring extra water additives and extra
filtering time. Do not allow swimming in pool until the pH level is balanced. Consult your local swimming
pool supply store for instructions.
Chlorinated water may damage lawns, gardens or shrubbery as children play in the pool and splash
water outside the pool. Lawn areas underneath the pool liner will be destroyed. Note that some types
of grass may grow through the liner.
Filter run time depends on pool size, weather and usage level. Experiment with various run times so
as to produce clean clear water.
European standard EN16713-3 lists some additional pool water quality and water treatment information
that can be found at www.intexcorp.com/support.
LONG TERM STORAGE & WINTERIZATION
CAUTION
Concentrated chlorine solutions may damage the pool liner. Always follow the
chemical manufacturer’s directions, and the health and hazard warnings.
CAUTION
Allowing the water to freeze will damage the sand filter and void the warranty.
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 21
TROUBLESHOOTING GUIDE
Line cord must be plugged into a 3 wire outlet
that is protected by a Class A Ground Fault
Circuit Interrupter, or RCD.
Reset circuit breaker. If circuit breaker trips
repeatedly, your electrical system may have a
defect. Turn off circuit breaker and call an
electrician to correct the problem.
Let the motor cool down and restart again.
Adjust the chlorine and pH level. Consult your local
swimming pool supply stores.
Load with filter sand, see “sand loading instructions”.
Set valve to “FILTER” position.
Operate the filter for longer periods.
Clean the strainer screen at the inlet.
Clear any obstructions in the intake hose by discharging it
inside pool wall.
Tighten hose nuts, check hoses for damage, check pool
water level.
Clean the pre-filtering basket more often.
• Backwash filter.
Install the nozzle at the upper position of the pool inlet, and
the strainer at the lower position of the pool outlet.
Remove about 1” of sand if necessary.
Remove any pool vacuuming device attached to the
system line.
Make sure the inlet threaded air connector is connected to
the pool inlet upper hole.
Fill pool to correct water level.
Clean strainer screens at pool inlet.
Tighten hose nuts, check hose for damage.
Contact Intex service center.
Remove 6-way valve cover and ensure the o-ring is in place.
Clean sand tank o-ring with garden hose water.
• Tighten securely.
Contact Intex service center.
Tighten/reinstall hose nut.
Ensure o-ring/L-shape o-ring is in place and
not damaged.
Turn off the pump and restart 5 minutes later.
Re-set the timer.
Contact Intex service center.
Clear any obstructions in the intake by
unscrewing it from the 6-way valve.
Contact Intex service center.
Use only No. 20 silica sand with particle size
range 0.45 to 0.85 mm (0.018 to 0.033 inches)
and a Uniformity Coefficient less than 1.75.
• Change sand.
Tighten or reinstall plunger valve.
Tighten air jet valve and make sure it’s
facing up.
Turn pump ON and run for few seconds, then
turn OFF, repeat 3 times.
Remove air jet valve, flush dirt out with water
and replace valve back.
Replace a new air jet valve.
FILTER MOTOR FAILS
TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN’T PUMP
WATER OR FLOW IS
VERY SLOW
PUMP DOESN’T
WORK
6-WAY VALVE/COVER
LEAKING
HOSE LEAKING
TIMER IS INACCURATE
OR TIMER CAN'T BE SET
PRESSURE GAUGE
DOESN’T WORK
SAND IS FLOWING
BACK INTO THE POOL
INLET THREADED
AIR CONNECTOR/AIR
JET VALVE LEAKING
The motor is not plugged in.
The GFCI/RCD circuit breaker
is tripped.
Motor too hot and overload
protection is shut off.
Improper chlorine or pH levels.
No filtering media in tank.
Wrong 6-way valve setting position.
Excessively dirty pool.
The strainer screen is restricting
the water flow.
Clogged inlet or discharge.
An air leak on the intake line.
Excessively dirty pool.
Sand media clogged with dirt.
Nozzle and strainer connections
are reversed.
Crusting or caking on the filtering
sand surface.
Pool vacuuming device attached
to the system.
Inlet threaded air connector
connected to the wrong hole on
the liner.
Low water level.
Strainer screen clogged up.
An air leak on the intake hose.
Faulty motor or the impeller is jammed.
Sand tank o-ring missing.
Sand tank o-ring dirty.
Flange clamp not tight.
6-way valve damage.
Hose nut not securely tight.
Hose connection fitting
o-ring/L-shape o-ring missing.
Possible inner timer defective.
Clogged inlet of the pressure
gauge.
Pressure gauge damage.
Sand is too small.
Sand bed is calcified.
Plunger valve not well-fitted.
Air jet valve is not tight and
facing up.
Air jet valve internal seal blocked.
Air jet valve internal seal dirty.
Air jet valve broken.
TROUBLE CAUSE SOLUTION
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 22
COMMON POOL PROBLEMS
PROBLEM DESCRIPTION CAUSE SOLUTION
ALGAE
COLORED
WATER
FLOATING
MATTER IN
WATER
CHRONIC LOW
WATER LEVEL
SEDIMENT
ON POOL
BOTTOM
SURFACE
DEBRIS
• Chlorine and pH levels
need adjustment.
• Copper, iron or maganese
in water being oxidized by
the added chlorine.
• "Hard water" caused by a
too high pH level.
• Chlorine content is low.
• Foreign matter in water.
• Rip or hole in pool liner or
hoses.
• The drain valves are loose.
• Heavy use, getting in
and out of pool.
• Pool too close to trees.
Super chlorinate with shock
treatment. Correct pH to your pool
store's recommended level.
Vacuum pool bottom.
Maintain proper chlorine level.
Adjust pH level to the
recommended level.
Run filter until water is clear.
Correct the pH level. Check with
your pool dealer for advice.
Adjust the chlorine level.
Repair with a patch kit.
Finger tighten all caps.
Use Intex pool vacuum to clean
bottom of pool.
Use Intex pool skimmer.
• Greenish water.
• Green or black
spots on pool liner.
• Pool liner is
slippery and/or has
a bad odor.
• Water turns blue,
brown, or black
when first treated
with chlorine.
• Water is cloudy or
milky.
• Level is lower than
on previous day.
• Dirt or sand on
pool floor.
• Leaves, insects
etc.
Water recreation is both fun and therapeutic. However, it involves inherent risks of injury
and death. To reduce your risk of injury, read and follow all product, package and package
insert warnings and instructions. Remember, however, that product warnings, instructions
and safety guidelines cover some common risks of water recreation, but do not cover all
risks and dangers.
For additional safeguards, also familiarize yourself with the following general guidelines as
well as guidelines provided by nationally recognized Safety Organizations:
Demand constant supervision. A competent adult should be appointed as a “lifeguard” or
water watcher, especially when children are in and around the pool.
Learn to swim.
Take the time to learn CPR and first aid.
Instruct anyone who is supervising pool users about potential pool hazards and about
the use of protective devices such as locked doors, barriers, etc.
Instruct all pool users, including children what to do in case of an emergency.
Always use common sense and good judgement when enjoying any water activity.
Supervise, supervise, supervise.
GENERAL AQUATIC SAFETY
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service Department
for assistance. See separate “Authorized Service Centers” sheet.
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 23
PARTS LIST
LIMITED WARRANTY
Your Sand Filter Pump has been manufactured using the highest quality materials and
workmanship. All Intex products have been inspected and found free of defects prior to
leaving the factory. This limited warranty applies only to the Sand Filter Pump and
accessories listed below.
This limited warranty is in addition to, and not a substitute for, your legal rights and remedies.
To the extent that this warranty is inconsistent with any of your legal rights, they take priority.
For example, consumer laws across the European Union provide statutory warranty rights in
addition to the coverage you receive from this limited warranty: for information on EU-wide
consumer laws, please visit the European Consumer Center website at http://ec.europa.eu/
consumers/ecc/contact_en/htm.
The provisions of this limited warranty apply only to the original purchaser and are not
transferable. This limited warranty is valid for the period noted below from the date of the
initial retail purchase. Keep your original sales receipt with this document, as proof of
purchase will be required and must accompany warranty claims or the limited warranty will
be invalid.
Sand Filter Pump Warranty – 2 Years
Hoses, Plunger Valves & Fittings Warranty – 180 Days
If you find a manufacturing defect in the Sand Filter Pump during the warranty periods noted
above, please contact the appropriate Intex Service Center listed in the separate “Authorized
Service Centers” sheet. If the item is returned as directed by the Intex Service Center, the
Service Center will inspect the item and determine the validity of the claim. If the item is
covered by the provisions of the warranty, the item will be repaired or replaced, with the
same or comparable item (at Intex’s choice) at no charge to you.
Other than this warranty, and other legal rights in your country, no further warranties are
implied. To the extent possibly in your country, in no event shall Intex be liable to you or
any third party for direct or consequential damages arising out of the use of your Sand Filter
Pump, or Intex or its agents’ and employees’ actions (including the manufacture of the
product). If your country does not allow the exclusion or limitation of incidental or
consequential damages, this limitation or exclusion does not apply to you.
You should note that this limited warranty does not apply in the following circumstances:
If the Sand Filter Pump is subject to negligence, abnormal use or application, accident,
improper operation, improper voltage or current contrary to operating instructions, improper
maintenance or storage;
If the Sand Filter Pump is subject to damage by circumstances beyond Intex’s control,
including but not limited to, ordinary wear and tear and damage caused by exposure to
fire, flood, freezing, rain, or other external environmental forces;
To parts and components not sold by Intex; and/or
To unauthorized alterations, repairs or disassembly to the Sand Filter Pump by anyone
other than Intex Service Center personnel.
The costs associated with the loss of pool water, chemicals or water damage are not covered
by this warranty. Injury or damage to any property or person is not covered by this warranty.
Read the owner’s manual carefully and follow all instructions regarding proper operation and
maintenance of your Sand Filter Pump. Always inspect your product prior to use. This limited
warranty will be void if use instructions are not followed.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Intex SF60220RC-2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Intex SF60220RC-2

Intex SF60220RC-2 Bedienungsanleitung - Deutsch - 23 seiten

Intex SF60220RC-2 Bedienungsanleitung - Holländisch - 24 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info