Bedienungsanleitung Intex SF70110-2 (Seite 15 von 24) (Englisch)

752309

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

342

SAVE THESE INSTRUCTIONS

(342PO) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 06/08/2018

English

Page 15

Initial startup and operation:

Before operating, be sure that:

• All the hoses have been connected and tightened securely, and correct amount of filter sand

have been loaded.

• The entire system is connected to a grounding type receptacle protected by a ground-fault

circuit interrupter (GFCI) or residual current device (RCD).

OPERATING INSTRUCTIONS (continued)

CAUTION

The filter control valve has a closed position. The pump should never be on when

the valve is in the closed position. If the pump is operated with the valve closed,

explosive situation could exist.

1. Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valves

to allow water to flow into the sand filter pump. With water flowing into sand filter pump, the

water pressure will allow the air trapped inside to escape from the air release valves (19).

When all the air has escaped water will flow out of the valves (19). When this occurs gently

finger tighten the valves (19) in a clockwise direction.

2. Ensure the drain/waste outlet on the 6-way valve is not

covered and directed to a proper draining receptacle.

3. Ensure the pump is off, depress the 6-way valve and turn

it to the “BACKWASH” position (see drawings 24 & 29).

IMPORTANT: To prevent damage to the 6-way valve,

always depress the valve handle before turning.

Always switch off pump before changing the 6-way

valve position.

4. Press to switch on the system, and then press to set

the operating TIMER hours (see “Operating the system under TIMER mode or manually”

section for details). Water is circulating backward through the sand media and to waste/drain

outlet. Backwash until a clear flow of water is observed in the waste/drain outlet or through

the drain sediment window.

NOTE: If the LED display flashes “00”, the device is in stand-by mode and the pump will not

operate. The initial backwash of the filter is recommended to remove any impurities or fine

sand particles in the sand media.

5. Switch off the pump, change the 6-way valve to “RINSE” position (see drawing 25).

6. Switch on the pump and run the pump for about one minute to level out the sand bed after

backwashing the sand media.

7. Switch off the pump, change the 6-way valve to “FILTER” position (see drawing 23).

8. Switch on the pump. The system is now operating in the normal filtering mode. Run the pump

until the desired pool water clearance is obtained and no more than 12 hours per day. For the

initial startup, it is recommended setting the system to a longer TIMER operating hours or “FP”

for the pump to operate continuously without the TIMER.

9. Record the initial pressure gauge reading when the filter media is clean.

NOTE: During initial setup of the system, it may be necessary to backwash frequently due to

unusual heavy dirt present in the water and sand. After that, as the filter removes dirt and

impurities from the pool water, the accumulated dirt in the sand media will cause the pressure

to rise and the flow to diminish. If there is no vacuuming device attached to the system and

the pressure gauge reading is in the yellow zone it is time to backwash the sand media, see

“BACKWASH” under “initial startup and operation” section. Vacuuming device (i.e. Intex auto

pool cleaner) attached to the system may also cause the flow to diminish and the pressure to

rise. Remove any vacuuming device from the system and check if the pressure gauge

reading has dropped from the yellow zone to the green zone.

10. Monitor the pressure gauge reading, and check that the inlet and outlet openings are not

obstructed on a weekly basis. If the pressure gauge indicates yellow it is time to backwash

the filter media.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex SF70110-2 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info