Bedienungsanleitung Intex SSP-10-1 PureSpa (Seite 8 von 27) (Englisch)

784580

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

346

S AVE THESE INSTRUCTIONS

(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019

English

Page 8

SET UP (continued)

Setup the spa with at least 2 persons.

1. Move the entire package to the selected site. Do not drag the spa tub across the ground as this can

cause damage and leakage.

Open the carton carefully as this carton can be used to store the spa during long term storage or when

not in use.

2. Lay out all the parts on the ground and make sure all the parts are accounted for. For missing or

damaged parts contact the appropriate Intex Service Center listed in the separate “Authorized service

Centers” sheet.

Safety Sign Card Posting

The Safety Sign card included with the manual shall be posted in an area visible to the users of the spa to

alert them of the safety rules and warnings. For replacement of the safety sign card, visit our website at

www.intexcorp.com for additional print copies. Laminate the printed safety sign copy for protection from the

elements.

Spa Control Panel Charging and Installation

1. Make sure the back of the control panel (3) and the control base recessed channel surface are clean

and dry.

2. Make sure the control base is plugged in and the RCD tested. Place the control panel (3) on the

control base recessed channel to charge the built-in battery (see drawing 1). See “Spa Control Panel”

operation section for more details.

3. Once the control panel battery is fully charged, you may place the control panel on top of the spa tub

wall (see drawing 2.1). To remove the control panel from the spa tub, lift the latch while pulling the

control panel away from the support stand (see drawing 2.2).

• Humidity is a natural side effect of indoor spa installation. The room shall be properly ventilated to allow

moisture to escape. Install a ventilating system to prevent excess condensation, moisture in the room.

Additional requirements for outdoor installation

• Spa owners may need to comply with local or states laws relating to childproof fencing, safety barriers,

lighting, and other safety requirements. Contact your local building code enforcement ofﬁ ce for further

details.

• Make sure the surface is level, ﬂ at, smooth and strong enough to support the full weight of the ﬁ lled spa.

• Do not setup the spa on grass or dirt, as this increases the amount of debris entering the spa, and

damage the spa ﬂ oor.

• Do not expose the spa to direct sunlight for extended period of time. Provide protection from the

sun such as sunshade, tent, awning or gazebo.

• It is possible to install and leave the spa outside at a temperature not lower than 4°C (39°F) provided the

water temperature inside the spa is higher than 4°C (39°F) and the water inside the circulation system,

pump, pipe are not frozen. Put a “temp barrier mat” between the spa ﬂ oor and the ground to prevent heat

loss from the bottom of the spa and to provide better heat retention. Do not use the spa if the ambient or

water temperature is 4°C (39°F) or lower.

• The spa control base unit shall be setup on a smooth and level cement ground.

32.2

2.1

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex SSP-10-1 PureSpa Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info