Bedienungsanleitung Intex SSP-H-10 PureSpa (Seite 14 von 27) (Englisch)

784581

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

346

S AVE THESE INSTRUCTIONS

(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019

English

Page 14

SPA CONTROL PANEL

F: Heat Button

G: Celsius/Fahrenheit Toggle Button

H: Heat System Delay Timer (HSDT) Button

I: Heat System Operating Hours (HSOH) Button

OPERATION (continued)

Heat Button: Press this button to activate the heating system. Press or to set the desired

water temperature. The system will heat the spa water until the water temperature reaches the

set temperature. When the spa water temperature drops 2°F below the set temperature the

heating system will restart. When the ﬂ ame icon on the display is red, the heating system is

activated. When the ﬂ ame icon turns green, the water is at the set temperature. The heating

system is at rest and the ﬁ ltration system will continue working nonstop. If the heating system is

activated the ﬁ lter pump will start at the same time.

NOTE: To stop the ﬁ ltration system while the heater is at rest mode, press the ﬂ ame button

ﬁ rst and then the ﬁ lter button. Pressing the heat button only while the heater is at rest mode will

turn off the heating system only and the ﬁ ltration system will operate for 1 more minute before it

turns off or continue with the ﬁ lter pump preset operating hours.

IMPORTANT: The following conditions will lead to slow water heating.

• The ambient temperature is lower than 50ºF (10ºC).

• Outdoor wind speed is above 3.5-5.4 m/s (8-12 mph).

• The air bubble function is activated when heating the spa water.

• The spa is not properly covered with the spa cover when the water is heating.

Celsius/Fahrenheit Toggle button: The temperature can be displayed in either Fahrenheit or

Celsius. The system’s default is Celsius.

NOTE: The default temperature is 68°F (20°C). Temperature adjustment ranges from 50°F

(10°C ) to 104°F(40°C).

CAUTION: NEVER use the spa if indicated water temperature is more than 104ºF(40°C).

Heat System Delay Timer (HSDT) Button: Press this button and then press or to set

the heating system starting time timer, from 001 to 120 hours. The icon will ﬂ ash red for a few

seconds and then stays red. Once the countdown timer reached 000, the heating system will

start operating. Repeat previous steps to reprogram this function. Set the Heat System Delay

Timer time to 000 to deactivate this function. Press the HSDT button twice any time to re-adjust

the preset hours.

Heat System Operating Hours (HSOH) Button: Press this button and then press or to

set the heating system operating hours from 000 to 048 hours. The icon will ﬂ ash red for a few

seconds and then stays red. The heating system will operate for the amount of preset hours

only regardless if the preset spa water temperature is reached or not. The information shown on

the LED display alternates between the remaining operating hours and the water temperature,

provided the HSDT function is not set. Repeat previous steps to reprogram this function. Set

the Heat System Operating Hours to 000 to deactivate this function. Press the HSOH button

twice any time to re-adjust the preset hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex SSP-H-10 PureSpa Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info