Bedienungsanleitung Intex Ultra XTR Frame - 26368NP (Seite 8 von 15) (Englisch)

686034

Zoom out

Zoom in

Vorherige Seite

1/15

Nächste Seite

119A

SAVE THESE INSTRUCTIONS

(119IO) ULTRA XTR™ RECTANGULAR / PRISM FRAME™ POOLS ENGLISH 7.5” X 10.3” PANTONE 295U 11/07/2018

English

Page 8

POOL SETUP (continued)

You may have purchased this pool with the Intex Krystal Clear™ filter pump. The pump has its

own separate set of installation instructions. First assemble your pool unit and then set up the

filter pump.

Estimated assembly time 60~90 minutes. (Note the assembly time is only approximate and

individual assembly experience may vary.)

1. • Find a flat, level location that is free and clear of stones, branches or other sharp objects that may

puncture the pool liner or cause injury.

• Open the carton containing the liner, joints, legs, etc., very carefully as this carton can be used to

store the pool during the winter months or when not in use.

• Remove the ground cloth (14) from carton. Spread

it out completely with its edges being at least

5 - 6’ (1.5 - 2.0 m) from any obstacle such as walls,

fences, trees, etc. Remove the liner (15) from carton

and spread it out over the ground cloth with the

drain valve towards the draining area. Place the

drain valve away from the house. Open it up to

warm it in the sun. This warming will make

installation easier. Make sure the liner is centered

atop the ground cloth. Be sure to face the end with

the 2 hose connectors towards the electrical

power source.

IMPORTANT: Do not drag the liner across the

ground as this can cause liner damage and pool

leakage (see drawing 1).

• During the set-up of this pool liner, point the hose

connections or openings in the direction of the

electric power source. The outer edge of the

assembled pool is to be within reach of the

electrical connection for the optional filter pump.

2. Remove all the parts from the carton(s) and place

them on the ground in the location where they are to

be assembled. Check the parts listing and be sure all

the pieces to be assembled are accounted for (see

drawings 2.1-2.4).

IMPORTANT: Do not start assembly if any pieces

are missing. For replacement pieces call the

Consumer Service telephone number in your area.

After all pieces are accounted for move the pieces

away from the liner for of installation.

NOTE: Sprinkle some talcum powder over the

horizontal beams before sliding them into the pool

liner sleeve. This will make removal of the beams

from the liner easier during the disassembly of the

pool.

ELECTRICAL SOURCE

5 - 6'

(1.5 - 2.0 m)

5 - 6' (1.5 - 2.0 m)

5 - 6'

(1.5 - 2.0 m)

LINER

2.1

157-1/2”x78-3/4”x39-3/8” /15’ X 9’ /16’ X 8’/ 18’ X 9’

(A)

CORNER JOINT

(F)

(D)

(F)

(D)

(C)

(A)

(C)

LINER

(B) (B)

2.3

(A)

CORNER

JOINT

CORNER

JOINT

CORNER

JOINT

CORNER

JOINT

(F)

(D)

(E)

(D)

(F)

(E)

(C)

LINER

(B) (B)

24’ X 12’

2.2

118-1/8”x68-3/4”

(A)

CORNER JOINT

(F)

(D)

(F)

(D)

(C)

LINER (E)

(B)

(E)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex Ultra XTR Frame - 26368NP Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Intex Ultra XTR Frame - 26368NP

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info