Bedienungsanleitung Intex ZS6110 Krystal Clear (Seite 14 von 23) (Englisch)

686153

Zoom out

Zoom in

Vorherige Seite

1/23

Nächste Seite

(328PO) MODEL ZS6110 OZONE & SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2017

328

SAVE THESE INSTRUCTIONS

English

Page 14

Boost cycle

•

After a heavy rain or if the pool is dirty, press and hold “BOOST” button

for 5 seconds until the indicator lights up and the LED display “80”.

This indicates that the Ozone & Saltwater system has started ozone

and more chlorine sanitizer production. You can press and hold the

“BOOST” button for another 5 seconds until the indicator is off, which

will cancel the Boost cycle.

•

The boost operating hours is 8 times the amount of time programmed into the system, i.e.

if your Ozone & Saltwater system operating time is 3 hours, the boost procedure will run

8 x 3 = 24 hours. After boost procedure has been completed, the system will automatically

switch to the normal working mode.

•

Once the boost is operating, check whether the filter pump operating hours have been set

properly. For example, the boost operating time is 16 hours, the filter pump should be set

to run for 17 hours at least. Increase the filter pump operating time if necessary.

Note:

If an Intex filter pump is attached to the system, set the pump switch to on “I” position.

Test pool water regularly:

Test the pool water every week to maintain the proper sanitizer level.

It’s very important that the free chlorine is between 0.5-3 ppm.

8. Stand-by/power saving mode:

•

When the cycle ends, the green “SLEEP” indicator on the control panel

lights up and the LED display flashes “93”. The system is now in

Stand-By mode. After a while, it shuts down and sets itself in a Power

Saving mode. The system will automatically turn itself back on in

24 hours, starting its daily cycle of chlorine production.

•

The “SLEEP” indicator stays on, while the system is in the Power Saving

mode. The LED display however, goes blank after 5 minutes. Press any

button ( or ) to view the last LED code.

Electrode Self-Clean cycle:

•

Press and hold button for 5 seconds until the LED display flashes “10”.

Depending on your pool water calcium hardness level, press button

again to select the self-clean cycle time as below. Total of 3 settings:

14 hours, 10 hours and 06 hours.

NOTE:

The life of the cell varies depending on water conditions, pool usage and operating

time of the device. Select 14 hours cycle time to maximize the life of the electrolytic cell if

the calcium hardness level is up to 150 ppm. Manual routine cleaning and maintenance will

further lengthen the life of the electrolytic cell.

•

With the desired self-clean hours showing, press button to lock the keypad controls and

the LED display will return to the normal operating time. The system will reverse the polarity

of the electrode

(5)

every time according to the selected hours.

NOTE:

If you forget to lock the keypad controls, the system will automatically lock it and start

working 5 seconds later.

OPERATION INSTRUCTIONS (continued)

Calcium Hardness Self-clean cycle time

0 - 150 ppm Reverse polarity every 14 hours

150 - 250 ppm Reverse polarity every 10 hours

250 - 350 ppm Reverse polarity every 06 hours

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Intex ZS6110 Krystal Clear Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info