Bedienungsanleitung Inventor P9VO32 Passion Eco (Seite 15 von 156) (Deutsch, Englisch)

771590

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

 Page 14 

If refrigerant piping is already embedded in

the wall, do the following:

Step 1:Hook the indoor unit on the mounting

plate:

Step 2: Prepare refrigerant piping:

1. Disassemble the louver:

Fig. 3.5

Move to left or right

30-50mm

(1.2-1.95in)

30-50mm

(1.2-1.95in)

1. Keep in mind that the hooks on the mounting plate

are smaller than the holes on the back of the unit.

If you find that you don’t have ample room to connect

embedded pipes to the indoor unit, the unit can be

adjusted left or right by about 30-50mm (1.25-1.95in),

depending on the model. (See Fig.3.4)

CAUTION

Be extremely careful not to dent or

damage the piping while bending them

away from the unit. Any dents in the

piping will affect the unit’s performance.

Step 4: Prepare refrigerant piping

The refrigerant piping is inside an insulating

sleeve attached to the back of the unit. You must

prepare the piping before passing it through the

hole in the wall. Refer to the Refrigerant Piping

Connection section of this manual for detailed

instructions on pipe ﬂaring and ﬂare torque

requirements, technique, etc.

NOTE ON PIPING ANGLE

Refrigerant piping can exit the indoor unit from

four different angles:

•

Left-hand side

•

Left rear

•

Right-hand side

•

Right rear

Refer to Fig. 3.3 for details.

Fig. 3.3

Fig. 3.4

2. Open and fix the position of the panel

Firstly, unscrew the two screws showed

in the picture below, then open the panel,

and fix the position of the panel by the

latch(see Fig.3.6).

 Page 15 

If there is no refrigerant piping embedded in

the wall, do the following:

Fig. 3.6

Fig. 3.7

Step 3. Connect drain hose and refrigerant

piping (refer to Refrigerant Piping Connection

section of this manual for instructions).

Step 4. Keep pipe connection point exposed to

perform the leak test (refer to Electrical Checks

and Leak Checks section of this manual).

Step 5. After the leak test, wrap the connection

point with insulation tape.

Step 6. Remove the bracket or wedge that is

propping with insulation tape.

Step 7. Using even pressure, push down on the

bottom half of the unit. Keep pushing down

until the unit snaps onto the hooks along the

bottom of the mounting plate.

1. Based on the position of the wall hole relative

to the mounting plate, choose the side from

which the piping will exit the unit.

2. If the wall hole is behind the unit, keep the

knock-out panel in place. If the wall hole is to

the side of the indoor unit, remove the plastic

knock-out panel from that side of the unit.

(See Fig. 3.8). This will create a slot through

which your piping can exit the unit. Use

needle nose pliers if the plastic panel is too

difficult to remove by hand.

Use scissors to cut down the length of the

insulating sleeve to reveal about 40mm (1.57in)

of the refrigerant piping. This serves two

purposes:

• To facilitate the Refrigerant Piping

Connection process.

• To facilitage Gas Leak Checks and enable

you to check for dents

Knock-out Panel

Fig. 3.8

3. Use the holder in the mounting plate to

prop up the unit, giving you enough room

to connect the refrigerant piping, signal cable,

and drain hose.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor P9VO32 Passion Eco Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor P9VO32 Passion Eco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info