Bedienungsanleitung Inventor P9VO32 Passion Eco (Seite 17 von 156) (Deutsch, Englisch)

771590

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

 Page 16 

4. Connect the indoor unit’s refrigerant piping

to the connective piping that will join the

indoor and outdoor units. Refer to the

Refrigerant Piping Connection section

of this manual for detailed instructions.

5. Based on the position of the wall hole

relative to the mounting plate, determine the

necessary angle of your piping.

6. Grip the refrigerant piping at the base of the

bend.

7. Slowly, with even pressure, bend the piping

towards the hole. Do not dent or damage the

piping during the process.

Step 5: Connect drain hose

By default, the drain hose is attached to the left-

hand side of unit (when you’re facing the back

of the unit). However, it can also be attached to

the right-hand side.

1. To ensure proper drainage, attach the drain

hose on the same side that your refrigerant

piping exits the unit.

2. Attach drain hose extension (purchased

separately) to the end of drain hose.

3. Wrap the connection point firmly with Teflon

tape to ensure a good seal and to prevent

leaks.

4. For the portion of the drain hose that will

remain indoors, wrap it with foam pipe

insulation to prevent condensation.

5. Remove the air ﬁlter and pour a small amount

of water into the drain pan to make sure that

water ﬂows from the unit smoothly.

NOTE ON DRAIN HOSE

PLACEMENT

Make sure to arrange the drain hose

according to Fig. 3.9

DO NOT kink the drain hose.

DO NOT

create a water trap.

DO NOT put the end of drain hose in

water or a container that will collect

water.

PLUG THE UNUSED DRAIN HOLE

To prevent unwanted leaks you must plug

the unused drain hole with the rubber plug

provided.

CORRECT

Make sure there are no

kinks or dent in drain

hose to ensure proper

drainage.

NOT CORRECT

Kinks in the drain hose

will create water traps.

NOT CORRECT

Do not place the end

of the drain hose in

water or in containers

that collect water. This

will prevent proper

drainage.

NOT CORRECT

Kinks in the drain hose

will create water traps.

Fig. 3.9

Fig. 3.10

Fig. 3.11

Fig. 3.12

 Page 17 

BEFORE PERFORMING

ELECTRICAL WORK, READ

THESE REGULATIONS

All wiring must comply with local and

national electrical codes, and must be

installed by a licensed electrician.

All electrical connections must be made

according to the Electrical Connection

Diagram located on the panels of the

indoor and outdoor units.

If there is a serious safety issue with

the power supply, stop work immediately.

Explain your reasoning to the client, and

refuse to install the unit until the safety

issue is properly resolved.

Power voltage should be within

90-110% of rated voltage. Insufficient

power supply can cause malfunction,

electrical shock, or fire.

If connecting power to fixed wiring,

install a surge protector and main

power switch with a capacity of 1.5

times the maximum current of the unit.

If connecting power to fixed wiring,

a switch or circuit breaker that

disconnects all poles and has a contact

separation of at least 1/8in (3mm) must

be incorporated in the fixed wiring.

The qualified technician must use an

approved circuit breaker or switch.

Only connect the unit to an individual

branch circuit outlet. Do not connect

another appliance to that outlet.

Make sure to properly ground the

air conditioner.

Every wire must be firmly connected.

Loose wiring can cause the terminal to

overheat, resulting in product

malfunction and possible fire.

10.

Do not let wires touch or rest against

refrigerant tubing, the compressor, or

any moving parts within the unit.

11.

If the unit has an auxiliary electric

heater, it must be installed at least 1

meter (40in) away from any

combustible materials.

Step 6: Connect signal cable

The signal cable enables communication between

the indoor and outdoor units. You must ﬁrst

choose the right cable size before preparing

it for connection.

Cable Types

•

Indoor Power Cable(if applicable):

H05VV-F or H05V2V2-F

•

Outdoor Power Cable:H07RN-F

•

Signal Cable:H07RN-F

Minimum Cross-Sectional Area of

Power and Signal Cables

Other Regions

Rated Current of

Appliance (A)

Nominal Cross-Sectional

Area (mm²)

> 3 and ≤ 6 0.75

> 6 and ≤ 10 1

> 10 and ≤ 16 1.5

> 16 and ≤ 25 2.5

> 25 and ≤ 32 4

> 32 and ≤ 40 6

CHOOSE THE RIGHT CABLE SIZE

The size of the power supply cable, signal

cable, fuse, and switch needed is determined

by the maximum current of the unit. The

maximum current is indicated on the nameplate

located on the side panel of the unit. Refer to

this nameplate to choose the right cable, fuse,

or switch.

WARNING

BEFORE PERFORMING ANY ELECTRICAL

OR WIRING WORK, TURN OFF THE MAIN

POWER TO THE SYSTEM.

North America

Appliance Amps (A) AWG

10 18

13 16

18 14

25 12

30 10

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor P9VO32 Passion Eco Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor P9VO32 Passion Eco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info