Bedienungsanleitung Inventor P9VO32 Passion Eco (Seite 19 von 156) (Deutsch, Englisch)

771590

Zoom out

Zoom in

Vorherige Seite

1/156

Nächste Seite

 Page 18 

TAKE NOTE OF FUSE SPECIFICATIONS

The air conditioner’s circuit board (PCB) is

designed with a fuse to provide overcurrent

protection. The speciﬁcations of the fuse

are printed on the circuit board, such as:

Indoor unit: T5A/250VAC

Outdoor unit(applicalbe to units adpot

R32 or R290 refrigerant only):

T20A/250VAC(<=18000Btu/h units)

T30A/250VAC(>18000Btu/h units)

NOTE: The fuse is made of ceramic.

Prepare the cable for connection:

Using wire strippers, strip the rubber jacket

from both ends of signal cable to reveal

about 40mm (1.57in) of the wires inside.

Strip the insulation from the ends of the

wires.

Using wire crimper, crimp u-type lugs on

the ends of the wires.

PAY ATTENTION TO LIVE WIRE

While crimping wires, make sure you clearly

distinguish the Live (“L”) Wire from other wires.

2. Open front panel of the indoor unit by loosen

the screws according to picture Fig.4.7, which

provide big space for wiring connection.

Open the wire box cover to connect the cable.

WARNING

4. Unscrew the cable clamp below the terminal

block and place it to the side.

5. Facing the back of the unit, remove the plastic

panel on the bottom left-hand side.

ALL WIRING MUST PERFORMED STRICTLY

IN ACCORDANCE WITH THE WIRING

DIAGRAM LOCATED ON THE INSIDE OF

THEINDOOR UNIT’S WIRE COVER.

Terminal

block

Wire

cover

Cable

clamp

Fig. 3.13

The Wiring Diagram is located

on the inside of the indoor unit’s

wire cover.

6. Feed the signal wire through this slot, from

the back of the unit to the front.

7. Facing the front of the unit, match the wire

colors with the labels on the terminal block,

connect the u-lug and and firmly screw each

wire to its corresponding terminal.

CAUTION

DO NOT MIX UP LIVE AND NULL WIRES

This is dangerous, and can cause the air

conditioning unit to malfunction.

8. After checking to make sure every connection

is secure, use the cable clamp to fasten the

signal cable to the unit. Screw the cable clamp

down tightly.

9. Replace the wire cover on the front of the

unit, and the plastic panel on the back.

NOTE ABOUT WIRING

THE WIRING CONNECTION PROCESS

MAY DIFFER SLIGHTLY

BETWEEN UNITS.

 Page 19 

Step 7: Wrap piping and cables

Before passing the piping, drain hose, and the

signal cable through the wall hole, you must

bundle them together to save space, protect

them, and insulate them.

1. Bundle the drain hose, refrigerant pipes, and

signal cable according to Fig. 3.14.

Indoor Unit

Space behind unit

Refrigerant piping

Drain hose

Signal wire

Insulation tape

DRAIN HOSE MUST BE ON BOTTOM

Make sure that the drain hose is at the bottom

of the bundle. Putting the drain hose at the

top of the bundle can cause the drain pan

to overﬂow, which can lead to ﬁre or water

damage.

DO NOT INTERTWINE SIGNAL CABLE WITH

OTHER WIRES

While bundling these items together, do not

intertwine or cross the signal cable with any

other wiring.

2. Using adhesive vinyl tape, attach the drain

hose to the underside of the refrigerant pipes.

3. Using insulation tape, wrap the signal wire,

refrigerant pipes, and drain hose tightly

together. Double-check that all items are

bundled in accordance with Fig. 3.14.

DO NOT WRAP ENDS OF PIPING

When wrapping the bundle, keep the ends

of the piping unwrapped. You need to access

them to test for leaks at the end of the

installation process (refer to

Electrical Checks

and Leak Checks

section of this manual).

Step 8: Mount indoor unit

If you installed new connective piping to the

outdoor unit, do the following:

1. If you have already passed the refrigerant

piping through the hole in the wall, proceed

to Step 4.

2. Otherwise, double-check that the ends of the

refrigerant pipes are sealed to prevent dirt or

foreign materials from entering the pipes.

3. Slowly pass the wrapped bundle of refrigerant

pipes, drain hose, and signal wire through the

hole in the wall.

4. Hook the top of the indoor unit on the upper

hook of the mounting plate.

5. Check that unit is hooked firmly on mounting

by applying slight pressure to the left and

right-hand sides of the unit. The unit should

not jiggle or shift.

6. Using even pressure, push down on the

bottom half of the unit. Keep pushing down

until the unit snaps onto the hooks along the

bottom of the mounting plate.

7. Again, check that the unit is ﬁrmly mounted

by applying slight pressure to the left and the

right-hand sides of the unit.

Fig. 3.14

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor P9VO32 Passion Eco Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor P9VO32 Passion Eco

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info