Bedienungsanleitung Inventor PR1VO32 Premium C (Seite 23 von 120) (Englisch)

771592

Zoom out

Zoom in

Vorherige Seite

1/120

Nächste Seite

 Page 22 

If you will install the unit on the ground or

on a concrete mounting platform, do the

following:

1. Mark the positions for four expansion bolts

based on dimensions in the Unit Mounting

Dimensions chart.

2. Pre-drill holes for expansion bolts.

3. Clean concrete dust away from holes.

4. Place a nut on the end of each expansion bolt.

5. Hammer expansion bolts into the pre-drilled

holes.

6. Remove the nuts from expansion bolts, and

place outdoor unit on bolts.

7. Put washer on each expansion bolt, then

replace the nuts.

8. Using a wrench, tighten each nut until snug.

WARNING

Step 3: Anchor outdoor unit

The outdoor unit can be anchored

to the ground or to a wall-mounted

bracket.

UNIT MOUNTING DIMENSIONS

The following is a list of different

outdoor unit sizes and the distance

between their mounting feet.

Prepare the installation base of the

unit according to the dimensions

below.

Air inlet

Air outlet

Air inlet

Air outlet

Air inlet

Fig. 4.5

WHEN DRILLING INTO CONCRETE, EYE

PROTECTION IS RECOMMENDED AT ALL

TIMES.

Outdoor Unit Dimensions (mm)

W x H x D

Mounting Dimensions

Distance A (mm) Distance B (mm)

681x434x285 (26.8”x17”x11.2”) 460 (18.10”) 292 (11.49”)

700x550x270 (27.5”x21.6”x10.62”) 450 (17.7”) 260 (10.24”)

780x540x250 (30.7”x21.25”x9.85”) 549 (21.6”) 276 (10.85”)

845x700x320 (33.25”x27.5”x12.6”) 560 (22”) 335 (13.2”)

810x558x310 (31.9”x22”x12.2”) 549 (21.6”) 325 (12.8”)

900x860x315 (35.4”x33.85”x12.4”) 590 (23.2”) 333 (13.1”)

945x810x395 (37.2”x31.9”x15.55”) 640 (25.2”) 405 (15.95”)

946x810x420 (37.21”x31.9”x16.53”) 673 (26.5”) 403 (15.87”)

946x810x410 (37.21”x31.9”x16.14”) 673 (26.5”) 403 (15.87”)

845x702x363 (33.25”x27.63”x14.29”) 540 (21.26”) 350 (13.8”)

700x550x275 (27.5”x21.6”x10.82”) 450 (17.7”) 260 (10.24”)

770x555x300 (30.3”x21.85”x11.81”) 487 (19.2”) 298 (11.73”)

800x554x333 (31.5”x21.8”x13.1”) 514 (20.24”) 340 (13.39”)

 Page 23 

If you will install the unit on a wall-mounted

bracket , do the following:

CAUTION

Before installing a wall-mounted unit, make

sure that the wall is made of solid brick,

concrete, or of similarly strong material. The

wall must be able to support at least four

times the weight of the unit.

Mark the position of bracket holes based on

dimensions in the Unit Mounting Dimensions

chart.

Pre-drill the holes for the expansion bolts.

Clean dust and debris away from holes.

Place a washer and nut on the end of each

expansion bolt.

Thread expansion bolts through holes in

mounting brackets, put mounting brackets

in position, and hammer expansion bolts into

the wall.

Check that the mounting brackets are level.

Carefully lift unit and place its mounting feet

on brackets.

Bolt the unit rmly to the brackets.

TO REDUCE VIBRATIONS OF WALL-

MOUNTED UNIT

If allowed, you can install the wall-mounted

unit with rubber gaskets to reduce vibrations

and noise.

Step 4: Connect signal and power cables

The outside unit’s terminal block is protected by

an electrical wiring cover on the side of the unit.

A comprehensive wiring diagram is printed on

the inside of the wiring cover.

BEFORE PERFORMING

ELECTRICAL WORK,

READ THESE REGULATIONS

All wiring must comply with local and

national electrical codes, and must be

installed by a licensed electrician.

All electrical connections must be made

according to the Electrical Connection

Diagram located on the side panels of the

indoor and outdoor units.

If there is a serious safety issue with the

power supply, stop work immediately. Explain

your reasoning to the client, and refuse

to install the unit until the safety issue is

properly resolved.

Power voltage should be within 90-110% of

rated voltage. Insufcient power supply can

cause electrical shock or re.

If connecting power to xed wiring, install a

surge protector and main power switch with

a capacity of 1.5 times the maximum current

of the unit.

If connecting power to xed wiring, a switch

or circuit breaker that disconnects all poles

and has a contact separation of at least 1/8in

(3mm) must be incorporated in the xed

wiring. The qualied technician must use an

approved circuit breaker or switch.

Only connect the unit to an individual branch

circuit outlet. Do not connect another

appliance to that outlet.

Make sure to properly ground the air

conditioner.

Every wire must be rmly connected. Loose

wiring can cause the terminal to overheat,

resulting in product malfunction and possible

re.

10. Do not

let wires touch or rest against

refrigerant tubing, the compressor, or any

moving parts within the unit.

11.

If the unit has an auxiliary electric heater, it

must be installed at least 1 meter (40in) away

from any combustible materials.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor PR1VO32 Premium C Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor PR1VO32 Premium C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info