Bedienungsanleitung Inventor U5MRT32 (Seite 9 von 144) (Deutsch, Englisch)

771601

Zoom out

Zoom in

Vorherige Seite

1/144

Nächste Seite

 Page 8 

Indoor Unit Installation 4

Indoor Unit Parts

Drain pump

(within indoor unit)

Drain pipe

Air outlet

Air inlet

Display panel

Front grille

Louver

Refrigerant pipe

Fig. 4.1

Safety Precautions

WARNING

• Securely install the indoor unit on a

structure that can sustain its weight. If the

structure is too weak, the unit may fall and

cause personal injury, unit and property

damage, or death.

• Install the indoor unit at a height of more

than 2.5m (8’) above the floor.

• DO NOT install the indoor unit in a

bathroom or laundry room as excessive

moisture can short the unit and corrode

the wiring.

CAUTION

• Install the indoor and outdoor units, cables,

and wires at least 1m (3.2’) from televisions

and radios to prevent static or image

distortion. Depending on the appliances,

a 1m (3.2’) distance may not be sufficient.

• If the indoor unit is installed on metal,

it must be electrically grounded.

 Page 9 

Table 4.1: Distance from ceiling relative to height of indoor unit

MODEL Length of A (mm/inch) Length of H (mm/inch)

18 205/8 > 235/9.3

24 205/8 > 235/9.3

30 205/8 > 235/9.3

30-48 245/9.6 > 275/10.8

48-60 287/11.3 > 317/12.5

Indoor Unit Installation Instructions

NOTE: Panel installation should be done after

piping and wiring.

Step 1: Select installation location

The indoor unit should be installed in a location

that meets the following requirements:

o The unit is at least 1m (39”) from the nearest

wall.

o There is enough room for installation and

maintenance.

o There is enough room for the connecting

pipe and drainpipe.

o The ceiling is horizontal and its structure

can sustain the weight of the indoor unit.

o The air inlet and outlet are not impeded.

o The airflow can fill the entire room.

o There is no direct radiation from heaters.

CAUTION

DO NOT install the unit in the following

locations:

In areas with oil drilling or fracking

In coastal areas with high salt content in the air

In areas with caustic gases in the air, such

as near hot springs

In areas with power fluctuations, such as

factories

In enclosed spaces, such as cabinets

In kitchens that use natural gas

In areas with strong electromagnetic waves

In areas that store flammable materials or

gas

In rooms with high humidity, such as

bathrooms or laundry rooms

RECOMMENDED DISTANCES BETWEEN THE INDOOR UNIT AND THE CEILING

The distance between the mounted indoor unit and the internal ceiling should meet the following

specifications. (See Fig. 4.2) Connecting point

of drain pipe Connecting point of

refrigerant pipe

(liquid side)

Connecting point of

refrigerant pipe

(gas side)

Front panel

Ground

Ceiling board

>2.5m / 8.2’

88cm / 34.5” (Ceiling hole)

Ceiling

Fig. 4.2

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor U5MRT32 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor U5MRT32

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info