Bedienungsanleitung Inventor V6MCRI32-18WiFiR (Seite 16 von 148) (Deutsch, Englisch)

771611

Zoom out

Zoom in

Vorherige Seite

1/148

Nächste Seite

Page 16 

 Page 16 

30 cm / 11.8” from back wall

60 cm / 23.6” on right

60 cm / 23.6” above

30 cm / 11.8” on left

200 cm / 78” in front

NOTE: The minimum distance between the

outdoor unit and walls described in the

installation guide does not apply to airtight

rooms. Be sure to keep the unit unobstructed

in at least two of the three directions (M, N, P)

(See Fig. 4.10)

Fig. 4.10

Fig. 4.11

NOTE: Make sure the water drains to a safe

location where it will not cause water

damage or a slipping hazard.

Seal

Drain joint

(A) (B)

Base pan hole of

outdoor unit

Seal

Fig. 4.12

Notes On Drilling Hole In Wall

You must drill a hole in the wall for the

refrigerant piping, and the signal cable that will

connect the indoor and outdoor units.

1. Determine the location of the wall hole

based on the location of the outdoor unit.

2. Using a 65-mm (2.5”) core drill, drill a hole

in the wall.

NOTE: When drilling the wall hole, make

sure to avoid wires, plumbing, and other

sensitive components.

3. Place the protective wall cuff in the hole.

This protects the edges of the hole and will

help seal it when you nish the installation

process.

Fig. 5.11

300 cm / 118” or more

60 cm / 23.6”

or more

150 cm / 59”

or more

25 cm / 9.8”

or more

25 cm / 9.8”

or more

Rows of series installation

L ≤ H L ≤ 1/2H

L A

25 cm / 9.8” or more

1/2H < L ≤ H

30 cm / 11.8” or more

L > H Can not be installed

Table 4.3 The relations between H, A and L

are as follows.

Drain Joint Installation

If the drain joint comes with a rubber seal

(see Fig. 4.12 - A ), do the following:

1. Fit the rubber seal on the end of the drain joint

that will connect to the outdoor unit.

2. Insert the drain joint into the hole in the base

pan of the unit.

3. Rotate the drain joint 90° until it clicks in place

facing the front of the unit.

4. Connect a drain hose extension (not included)

to the drain joint to redirect water from the

unit during heating mode.

If the drain joint doesn’t come with a rubber

seal (see Fig. 4.12 - B ), do the following:

Insert the drain joint into the hole in the base

pan of the unit. The drain joint will click in

place.

Connect a drain hose extension (not included)

to the drain joint to redirect water from the

unit during heating mode.

 Page 17 

NOTE ON DRAINPIPE INSTALLATION

•

When using an extended drainpipe, tighten

the indoor connection with an additional

protection tube to prevent it from pulling

loose.

•

The drainpipe should slope downward at a

gradient of at least 1/100 to prevent water

from ﬂowing back into the air conditioner.

•

To prevent the pipe from sagging, space

hanging wires every 1-1.5m (40-59”).

•

If the outlet of the drainpipe is higher than

the body’s pump joint, provide a lift pipe for

the exhaust outlet of the indoor unit. The

lift pipe must be installed no higher than

75cm (29.5”) from the ceiling board and

the distance between the unit and the lift

pipe must be less than 30cm (11.8”).

Incorrect installation could cause water to

ﬂow back into the unit and ﬂood.

•

To prevent air bubbles, keep the drain hose

level or slightly tiled up (<75mm / 3”).

The drainpipe is used to drain water from the

unit. Improper installation may cause unit and

property damage.

CAUTION

•

Insulate all piping to prevent condensation,

which could lead to water damage.

• If the drainpipe is bent or installed

incorrectly, water may leak and cause a

malfunction of the water- level switch.

• In HEAT mode, the outdoor unit will

discharge water. Ensure that the drain hose

is placed in an appropriate area to avoid

water damage and slippage due to frozen

drain water.

• DO NOT pull the drainpipe forcefully as

this could cause it to disconnect.

NOTE ON PURCHASING PIPES

This installation requires a polyethylene tube

(outside diameter = 3.7-3.9cm, inside diameter

= 3.2cm), which can be obtained at your local

hardware store or from your dealer.

Indoor Drainpipe Installation

Install the drainpipe as shown in Fig 5.2.

1. Cover the drainpipe with heat insulation to

prevent condensation and leakage.

2. Attach the mouth of the drain hose to the

unit’s outlet pipe. Sheath the mouth of the

hose and clip it rmly with a pipe clasp.

(Fig 5.1)

Drainpipe

connecting port

Drain hose

Metal clamp Insulation

Fig. 5.1

Drainpipe Installation 5

Downward slope

1/100

1-1.5m

(39-59”)

Fig. 5.2

Fig. 5.3

≤75cm

(29.5”)

Ceiling

1 - 1.5m

(39-59”)

0 - 75mm

(3”)

≤30cm (11.8”)

≤53cm

(20.8”)

22cm

(8.6”)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventor V6MCRI32-18WiFiR Seite 16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventor V6MCRI32-18WiFiR

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info