771741
23
Zoom out
Zoom in
Vorherige Seite
1/140
Nächste Seite
Page 23
8
Wiring
Safety Precautions
Outdoor Unit Wiring
WARNING
Be sure to disconnect the power supply before
working on the unit.
All electrical wiring must be done according to
local and national regulations.
Electrical wiring must be done by a qualied
technician. Improper connections may cause
electrical malfunction, injury and re.
An independent circuit and single outlet must
be used for this unit. DO NOT plug another
appliance or charger into the same outlet.lf the
electrical circuit capacity is not enough or there
is a defect in the electrical work, it can lead to
shock, re, unit and property damage.
Connect the power cable to the terminals and
fasten it with a clamp. An insecure connection
may cause re.
Make sure that all wiring is done correctly and
the control board cover is properly installed.
Failure to do so can cause overheating at the
connection points, re, and electrical shock.
Ensure that main supply connection is made
through a switch that disconnects all poles, with
contact gap of a least 3mm (0.118”).
DO NOT modify the length of the power cord
or use an extension cord.
WARNING
Before performing any electrical or wiring
work, turn o the main power to the system.
CAUTION
Connect the outdoor wires before connecting
the indoor wires.
Make sure you ground the unit. The ground-
ing wire should be away from gas pipes, wa-
ter pipes, lightning rods, telephone or other
grounding wires. Improper grounding may
cause electrical shock.
DO NOT connect the unit with the power source
until all wiring and piping is completed.
Make sure that you do not cross your electrical
wiring with your signal wiring, as this can cause
distortion and interference.
Follow these instructions to prevent distortion
when the compressor starts:
The unit must be connected to the main
outlet. Normally, the power supply must
have a low output impedance of 32 ohms.
No other equipment should be connected
to the same power circuit.
The unit’s power information can be found
on the rating sticker on the product.
TAKE NOTE OF FUSE SPECIFICATIONS
The air conditioner’s circuit board(PCB) is
designed with a fuse to provide overcurrent
protection. The specications of the fuse are
printed on the circuit board, such as:
Indoor unit: T5A/250VAC,T10A/250VAC. (ap-
plicable for unit adopts R32 refrigerant)
Outdoor unit: T20A/250VAC(for <24000Btu/h
unit),T30A/250VAC(for >24000Btu/h unit)
NOTE: The fuse is made of ceramic.
1. Prepare the cable for connection
a. You must first choose the right cable size
before preparing it for connection. Be sure
to use H07RN-F cables.
Table 8.1: Minimum Cross-Sectional Area of
Power and Signal Cables North America
Rated Current of Appliance (A) AWG
<7 18
7-13 16
13-18 14
18-25 12
25-30 10
23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Inventor V6MKI32-WiFi wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Inventor V6MKI32-WiFi

Inventor V6MKI32-WiFi Bedienungsanleitung - Deutsch, Englisch - 44 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info