551576
21
Zoom out
Zoom in
Vorherige Seite
1/28
Nächste Seite
MOUNTING AGAINST THE WALL
Attention: the cooker hood should be mounted onto a flat perpendicular kitchen wall.
Use the provided screws and plugs for mounting against the wall.
Measure the right height for the cooker hood (min. 65/75 cm) and mark the underside of the cooker hood on the wall.
Open the glass visor gently by pulling it towards you.
Remove the grease filters to expose the interior of the cooker hood. A keyhole slot (A) and a retainer hole (B) will be visible on
either side of the back panel.
Hold the cooker hood level against the wall on the correct height according to the marking and mark the holes (A+B) on the wall.
Drill the holes with a masonry drill off Ø8mm at the top of each marked slot and push in a rawl plug in each hole.
Partly insert two screws in the plugs, with a head diameter slightly smaller than the lower opening in the keyhole slot. Leave
about 5 mm of the screw sticking out.
Lift the cooker hood and slide the keyhole slots over the two screws.
Mark the two lower retainer holes and lift the cooker hood down.
Drill the holes with a masonry drill of Ø8mm and insert the plugs.
Mount the cooker hood and place the screws in the retainer holes. Tighten all four screws.
Replace the grease filters.
Place an exhaust-air pipe when you have chosen a duct as the extraction system.
Plug in the appliance.
MOUNTING BELOW A KITCHEN CUPBOARD
Attention: if the cooker hood it to be mounted underneath a cupboard, also take the minimum height (min. 65/75 cm) into
account. Use the provided bolts, nuts and washers for mounting underneath the cupboard.
Advice: Use the provided drilling template to mark the necessary holes for the bolts and for the hole of the exhaust when
connecting the cooker hood to a duct.
Open the glass visor by pulling it gently towards you.
Remove the grease filters to expose the interior of the cooker hood.
Hold the cooker hood underneath the cupboard and mark the four retainer holes (B) and mounting aid holes (A) at the bottom
of the cupboard.
Tape the drilling template to the bottom of the cupboard aligned with the marked positions and draw the hole for the power
cord and the exhaust pipe (C).
ø 120
90
545
35
225
112,5
42
16
70
ø 120
543
260
92
150
A A
B B
C
ø 120
90
545
35
225
112,5
42
16
70
ø 120
543
260
92
150
A A
B B
C
B B
English 21
AKO6001-AKO6002-instructions.indd 21 27-8-2014 11:16:44
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Inventum AKO6002 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info