Bedienungsanleitung Inventum BC18 (Seite 31 von 36) (Deutsch, Englisch, Holländisch, Französisch)

54538

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

• Remove

the battery

compartment

cover (left side

of the unit).

• Insert two 1,5

V AAA batteries

(Alkaline Type LR 03). Make absolutely sure that you insert

the batteries with the correct polarity as marked. Do not

use rechargeable batteries.

• Replace the battery cover carefully.

If the change battery icon is displayed, measurement is

no longer possible and you must replace all the batteries.

Note: Batteries containing pollutant substances are marked

as follows: Pb = Battery contains lead, Cd = Battery contains

cadmium, Hg = Battery contains mercury.

It is vital to set date and time. Only this way is it possible to

save and subsequently retrieve your measured values with

the right date and time. Time is shown in 24 hour format.

Note: if you hold down the buttons “down” or “up”,

you can set the values more quickly.

• Press “MODE”. The month starts ashing. Using the buttons

“down” or “up”, set the month 1 to 12 and conrm

with “MODE”.

• Set the day, hour and minute and conrm in each case with

“MODE”.

Setting individual warning limits (Doctor’s function)

After conrming date and time, the warning limits for

systolic and diastolic for each individual user can be set

individually. With the adjustment possibility, medical

instructions in the case of outpatient blood pressure

monitoring can be ideally implemented - Doctor’s function.

Note: the factory-set values are based on WHO guidelines for

high-normal and amount to 130 mmHg (systolic) and 85

mmHg (diastolic) (entry limit range). See the WHO-chart

shown. You must conrm the factory setting in order to

activate the Doctor’s function.

• Setting warning limits always begins with User 1.

• Unless the factory setting has been changed, the display

will read ‘--’.

• You can now alter the limits for systolic pressure with the

buttons “down” and “up” in 5 mmHg stages.

• Conrm the required value with the “MODE” button.

• You can now also change the limits for diastolic pressure

with the buttons “down” and “up” in 5 mmHg

stages.

• With the “MODE” button, save the settings and switch to

the next user memory, you can also save the settings with

“START/STOP” but then you go into measurement mode. If

you do not press any button, the instrument automatically

switches off after one minute.

Note

• From a medical point of view, the distance between

systolic and diastolic should be greater than 30 mmHg. A

systolic limit value below 100 mmHg and a diastolic limit

below 60 mmHg is not recommended.

• According to WHO Guidelines/Denitions and the latest

ndings, the test results can be classied and evaluated

according to the following chart.

4 | INSERTING/ CHANGING BATTERIES

5 | SETTING DATE, TIME & WARNING LIMITS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventum BC18 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info