Bedienungsanleitung Inventum KP511 (Seite 7 von 16) (Deutsch, Englisch, Holländisch, Französisch)

551630

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Before you use the appliance for the ﬁrst time, please do

as follows: Carefully unpack the appliance and remove

all the packaging material. Keep the material (plastic

bags and cardboard) out of reach of children. Check the

appliance after unpacking for any damage, possible from

transportation. Place the appliance on a stable and heat

resistant surface. Clean the appliance with a damp cloth.

The hotplate(s) has (have) a protective layer which should

be removed before the ﬁrst use. Switch the hot plate

on for about 5 to 6 minutes on the maximum position.

There can be a slight development of smoke from the

protective layer which is now burning of. After removing

the protective layer you can now switch the hot plate of or

begin using it.

2 | BEFORE FIRST USE

4 | CLEANING & MAINTENANCE

• If the appliance is used for other purposes than intended,

or is it not handled in accordance with the instruction

manual, the full responsibility for any consequences will

rest with the user. Any damages to the product or other

things are not covered by the warranty.

3 | OPERATION

The thermostat button is adjustable:

OFF = o

MIN = low

MAX = high

Make sure the thermostat button is set to position «OFF»

before you switch on the appliance. Plug the appliance

into a socket.

For heating the hot plate(s) turn the knob clockwise. The

red control light will burn. Position «MIN» is the lowest

position and position «MAX» is the highest position. It

takes about 10 minutes before the hot plate has reached

the maximum temperature (on the maximum position of

the thermostat knob). If the temperature is reached which

conforms to the set position, the control light will go out.

After a temperature drop, giving of heat to the pan, the

thermostat and the control light will switch on.

ATTENTION: THE APPLIANCE CAN GET HOT DURING USE.

THEREFORE ALWAYS PLACE THE APPLIANCE ON A HEAT

RESISTANT SURFACE AND NEVER ON A PLASTIC TABLE

OR PLASTIC TABLE CLOTH.

Use only pots with a bottom which has the same cross-cut

as the hot plate. A smaller cross-cut will lead to energy

loss. Model KP511 has a cast iron plate with a cross-cut of

185 mm. Model KP521 has a cast iron plate with a cross-

cut of 185 mm and a cast iron plate with a cross-cut of

155 mm.

Do not touch the hot plate when in use. Be careful: the

hot plates need time to cool down after switching the

appliance of. Always unplug the hot plate after every use.

Let the appliance cool o and always unplug the appliance

before cleaning. Wipe the outside of the appliance with a

damp cloth and dry the kettle afterwards. Never use any

abrasives! Be aware of the fact that the appliance needs

time to cool down after switching of. Never immerse the

appliance in water or others liquids.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventum KP511 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info