Bedienungsanleitung Inventum LK010 (Seite 29 von 44) (Englisch, Holländisch)

704940

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Connection with a stable pipework

The cooker comes with a G ½” threaded coupling. The connection to gas supply must be done in a manner that excludes stresses in

any point of the pipework or parts of the appliance. Make sure you do not exceed the torque when making the connection (maximum

torque is 20 Nm). Otherwise, the connection may be faulty or leaks may occur.

The gas hose should not touch metal elements of the cooker back shield.

Important! Each time you replace a reducer, carry out technical inspection of the cooker that covers gas valves and proper

operation of the flame failure cut-off device.

Caution! On completion of the cooker installation, the tightness of all connections should be checked, e.g. applying water with

soap. Do not use fire to check tightness.

ELECTRICAL CONNECTION

ADAPTING THE COOKER TO ANOTHER TYPE OF GAS

This operation may only be carried out by an appropriately authorised ﬁtter.

If the gas the cooker is to be supplied with differs from the gas provided for the cooker by the manufacturer, that is G20 / 25 mbar,

burner nozzles must be exchanged and the ﬂame needs to be adjusted.

In order to adapt the cooker to burn a different type of gas, you should:

• exchange the nozzles (see the gas tables below);

• adjust the “economical” ﬂame.

Caution! The cookers provided by the manufacturer have burners which are factory-adapted to use the gas specified on their rating

labels.

Gas table

Burner ﬂame Re-arming from liquid gas to natural gas Re-arming from natural gas to liquid gas

Full

1. Exchange a burner nozzle for the appropriate

type according to the gas table.

1. Exchange a burner nozzle for the appropriate

type according to the gas table.

Economical

2. Unscrew an adjusting bolt slightly and adjust

the ﬂame size.

2. Screw in an adjusting bolt slightly and check

the ﬂame size.

In order to perfom adjusting operations, take off the knobs.

Surface burners applied do not require adjustment of primary air. A correct ﬂame has distinct internal cones of blue and green colour.

A short, humming ﬂame or long, yellow and smoking one, without clearly outlined cones, shows improper quality of gas in the house-

hold piping or a damaged or soiled burner. In order to check a ﬂame, heat a burner for around 10 minutes with a full ﬂame, and next

turn the valve knob to the economical ﬂame position. The ﬂame should not go out or jump onto the nozzles.

• The cooker is manufactured to work with a one-phase alternating current (230V 1N~50Hz) and is equipped with a 3 x

1,5 mm

connection lead of 1.5 m length with a plug including a protection contact.

• A connection socket for electricity supply should be equipped with a protection pin and may not be located above the

cooker. After the cooker is positioned, it is necessary to make the connection socket accessible to the user.

• Before connecting the cooker to the socket, check if:

- the fuse and electricity supply are able to withstand the cooker load,

- the electricity supply is equipped with an efficacious ground system which meets the requirements of current

standards and

provisions.

- the plug is within easy reach.

English • 29

G25.3/25 mbar* G20/20 mbar G30/30 mbar

SOMIPRESS burners

Injector

diameter

Injector mark

Injector

diameter

Injector mark

Injector

diameter

Injector mark

1 0.70 mm 71 0.72 mm 72 0.52 mm 52 1 Simmer burner 1.0 kW

2 0.98 mm 98 0.98 mm 98 0.67 mm 67 2 Semi-rapid burners 1.8 kW

3 1.17 mm 116 1.17 mm 117 0.83 mm 83 1 Rapid burner 2.8 kW

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventum LK010 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Inventum LK010

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info