Bedienungsanleitung Inventum VKG6010 (Seite 17 von 24) (Englisch, Holländisch)

616186

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

faults

If the hob does not function properly, according to you, please try to solve the problem ﬁrst by checking the points in the table below

before contacting the customer department.

Fault Possible cause Solution

There is a smell of gas near

the hob.

The hob connection is leaking. Turn off the main gas supply valve. Contact your

installer.

A burner does not ignite. • The plug is not in the socket.

• A fuse is defective/ or switched off

in the fuse box.

• Ignition is dirty/damp.

• The burner parts are not placed

correctly.

• The burner parts are dirty/damp.

• The main gas suplly valve is closed.

• A fault in the gas mains.

• Wrong type of gas used.

• Put the plug into the socket.

• Replace the fuse or switch on the fuse in the fuse

box.

• Clean/dry the ignition.

• Reﬁt the burner and watch the openings for the

thermocouple and the ignition.

• Clean/dry the burner parts.

• Open the main gas valve.

• Consult your gas supplier.

• Check whether the gas used is suitable for the

appliance. Contact your installer if it is not correct.

The burner extinguishes

immediately after igniting.

• The control knob has not been

pressed long and/or deep enough

(at least 3 seconds).

• The thermocouple is dirty.

• Keep the control knob fully pressed for at least 3

seconds between the highest and the lowest ﬂame

setting. This can take longer the ﬁrst time because of

the gas supply.

• Clean/dry the thermocouple.

The burner does not burn

evenly.

• The burner parts are not placed

correctly.

• The burner parts are dirty/damp.

• The wrong type of gas is used.

• Reﬁt the burner and watch the openings for the

thermocouple and the ignition.

• Clean/ dry the burner parts.

• Check whether the gas used is suitable for the

appliance. Contact your installer if it is not correct.

cleaning & maintenance

Clean the hob after each use to maintain it in good condition. Food residue can create stubborn stains if not removed directly after

use.

Use a mild cleaning detergent to clean the hob. Burner parts and the pan supports should not be cleaned in the dishwasher. The

dishwasher detergent can corrode the materials.

The pan supports, burners and burner caps are removable for easy cleaning of the hob.

• First clean the control knobs, burners, burner caps and pan supports.

• Check whether the thermocouple and ignition are clean. If necessary use a toothpick or needle.

• Clean the drip tray.

• Clean everything again with just a damp cloth and dry it thoroughly.

• Reﬁt the burners. Make sure the openings are aligned for the thermocouple and the ignition.

• Reﬁt the burner caps.

• Reﬁt the pan supports. Place them carefully on the drip tray without sliding.

PERSISTENT STAINS

Persistent stains on the pan supports and burner caps can best be removed with a ﬂuid detergent or a plastic scouring sponge. Never

use aggressive cleaning products or sharp objects to clean the hob.

The surface of the drip tray can discolour slightly over time. This is normal and is not covered by the warranty.

English • 17

VKG6010-instructions.indd 17 15-12-2014 12:10:15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Inventum VKG6010 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info