459176

Inverto IDL5550S Seite 20

20
Zoom out
Zoom in
Vorherige Seite
1/124
Nächste Seite
En
17
There are three ways to update the software of the digital receiver:
Over The Antenna (OTA), Over The Cable (OTC), and through the USB port. In the next chapters you can nd
more detailed information about OTA and OTC. From the Settings Menu, select System Information and then
Software Update.
SOFTWARE UPDATE VIA ANTENNA (OTA)
If “Auto Upgrades” in the User Preferences is set to “Auto”, the receiver will do this all in the background during
stand by. At the rst start after such an update, the receiver will show you a popup message with the information,
that your receiver got a successful update.
During the OTA software update, the unit will rst search for the update signal.
During the search, a message box “Software update” will be displayed on the TV screen – this process may take
several minutes. To stop this process, press the “Red” function key or “Exit” key. If new software is available,
the user will be informed and asked to conrm the download.
The user will be asked to conrm the download two times, to help prevent accidental changes.
During the download, the “OTA” message will be displayed on the TV screen, showing the progress bar. After all
data has been received, the receiver will update the current software and automatically restart.
All user preferences and channel lists will remain unchanged.
Note: OTA Updates are broadcasted over ASTRA 19.2E satellite and therefore are not available in all the
countries.
SOFTWARE UPDATE VIA SERIAL CABLE (OTC)
In order to update the software using the service port on the rear panel, the user will require a RS232 cable, PC
with RS232 connection, and terminal software for the PC, such as HyperTerminal in Windows.
The user must also have the software le, which can be downloaded from the internet at www.ftacom.com.
To update the software using the cable, use the following steps:
1 – Switch the digital receiver off using the main power switch on the rear panel.
2 – Connect the digital receiver to the PC using a RS232 cable.
3 – In the terminal software of the PC, open a communication port with following parameters: 115200bps, 8bit,
1stop bit, no parity and no ow control.
4 – Select the new software le to send to the unit and set the protocol to 1k X modem.
5 – Start sending the le.
6 – Switch on the digital receiver to start the loading procedure.
During the transfer, the receiver will display the message “OTC” with a progress bar. After the le has been
received and unpacked, the digital receiver will update the current software and automatic restart. All user
preferences and channel lists will remain unchanged.
SOFTWARE UPDATE VIA USB
The software can be updated using a USB mass storage device.
To update the software using a USB mass storage device, you will require the new software le from our website
and a USB device, such as a USB hard disk or memory stick.
a) Copy the software bin le to the root folder of the USB mass storage device.
b) Make sure the receiver is switched off.
c) Turn the receiver On while the “+” button is pressed until “On The USB” messaged is displayed on
the front panel display
d) Insert the USB mass storage device into the USB slot on the front panel of the receiver.
e) The receiver will automatically copy the new software from the USB device into the receiver.
After the le has been installed and unpacked, the receiver will update the current software and automatically
restart. All user preferences and channel lists will remain unchanged.
Caution: Be careful not to interrupt the software installation by removing the USB stick, turning off the receiver,
or otherwise interrupting the installation process. If the installation is interrupted by accident, such as by a
power failure, the receiver may not boot up afterwards. If so, you can recover normal operation by installing new
software using the RS232 connection, or by returning the receiver for service.
Note: Installation of a complete software bundle, including boot loader, will reset all user settings and erase the
channel list. The library will remain unchanged.
Software update
… 20 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Inverto IDL5550S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info