Bedienungsanleitung Invicta Symphonia (Seite 15 von 44) (Englisch)

744562

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

Energy Distribution 2015 15

• Be sure to follow the manufacturer’s instructions

to maintain an effective vapor barrier at the

location where the chimney of other component

penetrates the exterior of the structure

• It is very important to follow minimum clearances

for chimney connectors to combustibles such as

walls and ceilings when installing the stove.

Typical chimney connector clearances are

outlined below. The single wall clearances are

generic; the double wall clearances shown are

specifically for Security brand and may vary with

other brands. Check the specifications from

the manufacturer of your connector.

COMPONENTS OF A VENTING SYSTEM

The complete venting system consists of several

components: chimney connector, wall thimble, wall

pass-through, chimney, and liner. It is absolutely

necessary that you install all of these components

and maintain the clearances to combustibles

discussed earlier to ensure a safe stove installation.

To protect against the possibility of a house fire, you

must properly install and constantly maintain the

venting system in good condition. Be sure to inspect

the chimney and chimney connector and keep it clean.

Upon inspection, immediately replace rusted,

cracked, or broken components. Failure to follow

these instructions and specified components or using

make-shift compromises can result in fire, property

damage, bodily injury, and even death.

• The chimney connector is the stovepipe from the

woodstove to the chimney. The chimney

connector stovepipe is 7" (178 mm) diameter, 24

MSG or 25 MSG blued steel connector pipe. Do

not use aluminum or galvanized steel pipe - they

cannot withstand the extreme temperatures of a

wood fire.

• The thimble is a manufactured (or

siteconstructed) device installed in combustible

walls through which the chimney connector

passes to the chimney. It keeps the walls from

igniting. You must use a wall thimble when

installing a chimney connector through a

combustible wall to the chimney.

• A wall pass-through (or chimney support

package) also keeps the walls from igniting. You

must use one when connecting through a wall or

ceiling to a prefabricated chimney.

• Only install this stove to a lined masonry chimney

or an approved high temperature prefabricated

residential type building heating appliance

chimney. Do not connect this stove to a chimney

serving another appliance; you will compromise

the safe operation of both the wood stove and the

connected appliance.

• A liner is the UL 1777 or ULC S635 (for factory

built fireplace or masonry) chimney.

You must connect your stove to a chimney

comparable to those recommended in this manual. Do

not use stovepipe as a chimney. Use stovepipe for

freestanding installations only to connect the stove to

a proper chimney.

• WARNING: DO NOT CONNECT THIS APPLIANCE

TO ANY AIR DISTRIBUTION DUCT OR SYSTEM.

INSTALLING A VENTING SYSTEM

Attach stovepipe sections to the flue collar and to each

other with the crimped end toward the stove. If

creosote builds up, this allows the creosote to run into

the stove and not on the outside of the stovepipe or

onto the stove.

Secure all joints, including attaching the stovepipe to

the stove's flue collar, with three sheet metal screws.

Install #10 x 1/2" (3 mm x 13 mm) sheet metal screws

into the holes pre-drilled in the flue collar.

Disregarding the screws can cause joints to separate

from the vibrations that result from a creosote

chimney fire.

You can simplify connecting stovepipe by using

additional accessories such as telescoping pipes, slip-

connectors or clean-out tees. These accessories ease

the periodic inspection of your chimney, as well as

allow you to dismantle the stovepipe easily (without

moving the stove).

Install the stove as close as practical to the chimney,

while maintaining all proper clearances. Install

stovepipe that is as short and as straight as possible.

Horizontal runs of stovepipe must always rise away

from the stove at a minimum of 1/4" per foot

(21mm/m).

We do not recommend long runs of stovepipe to

increase heat dispersal. Longer lengths of stovepipe,

or more connecting elbows, than necessary increase

the chances of draft resistance and the accumulation

of creosote buildup.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Invicta Symphonia Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info