Bedienungsanleitung Irobot roomba pro elite (Seite 8 von 14) (Englisch)

318183

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

2. Determine a suitable location for the Wall Mount Unit.Be sure

to leave at least 10”of clearance above the Wall Mount Unit

(beneath any shelving, for instance) to lift your Roomba in and

out comfortably.Also,leave 10”of clearance below the Wall Mount

Unit to empty Roomba’s Particle Bin while stowed (Figure 13a).

If possible, find a location near enough to an electrical outlet for

the Charger AC Adapter to reach the Wall Mount Unit.

Note:

Roomba fits snugly in the Wall Mount Unit.It may require some

force to lift Roomba out.Be sure to position Roomba in a location

where you have plenty of leverage.

3. Using a pencil,mark the locations of the holes to be drilled on the

wall (Figure 13c).

4. Remove the Wall Mount Unit and drill the five pilot holes in the

wall. Use a 1/4”drill bit to use the included wall anchors (best for

drywall or plaster),or an 1/8”drill bit if using just the included

screws without wall anchors (best for wood).If using the wall

anchors,hammer the wall anchors into the holes until they are

flush with the wall surface (Figure 13d).

5. Affix the Wall Mount Unit to the wall by screwing in the included

screws with a #2 Phillips screwdriver (Figure 14a).

6. Insert the rubber screw hole plugs into the screw holes to finish

installation (Figure 14b).

7. Press the Charger AC Adapter’s cord into the Charge Cord Pincer on

the bottom right side of the Wall Mount Unit as shown,and plug

the Charger AC Adapter into a standard U.S.electrical outlet.

Using the Wall Mount Unit

Roomba may be stored and charged in the Wall Mount Unit as needed

in between floor cleanings.To lift Roomba in and out of the Wall Mount

Unit, firmly grasp Roomba’s handle in one hand and use the other hand

to steady Roomba.Alternatively, you can grasp Roomba securely with

both hands (Figure 16).

Figure 14a-b (Pro Elite only): Securing

the Wall Mount Unit.Affix the Wall

Mount Unit to the wall by screwing in

the included screws with a #2 Phillips

screwdriver (Figure 14a).Insert the

rubber screw hole plugs into the

screw holes to finish installation

(Figure 14b).

Figure 15 (Pro Elite only): Trap a few

inches of the Charger AC Adapter’s

cord in the Charge Cord Pincer on the

bottom right side of the Wall Mount

Unit for easy charging when Roomba

is stowed away.

Figure 13a-d (Pro Elite only):

Preparing to mount the Wall

Mount Unit.Hold up the Wall

Mount Unit as shown on the

wall where you want to store

Roomba, leaving enough clear-

ance above and below the Unit

(Figure 13a).Using a pencil,mark

the locations of the holes to

be drilled on the wall (Figure

13c).Remove the Wall Mount

Unit and drill the five pilot

holes in the wall.Hammer the

wall anchors into the holes

(Figure 13d).

10"

• Keeping tabs on Roomba’s state: The Roomba Remote has all the same buttons as on Roomba Pro | Pro Elite,but

its buttons do not light up as they do on Roomba to help keep you informed of Roomba’s state.Always look at Roomba

to determine it’s state.

• The Pause Button: The red Pause Button on the Roomba Remote may be pressed during any cleaning cycle to Pause

Roomba. This button may be thought of as a “panic button”: it only pauses Roomba.Once Roomba is paused, additional

presses of this button have no effect.

Tip: Can’t find Roomba once it’s finished its work? Point the Roomba Remote in the general direction that you think

Roomba may be hiding.Press the Power Button on the Roomba Remote over and over.If Roomba can “see”the Remote,

it will beep to start up.

Using the Roomba Remote with Roomba Pro

The Roomba Remote is designed for use with Roomba Pro Elite,but is also compatible with Roomba Pro.As an added

benefit for Roomba Pro owners,all of the features of Roomba Pro Elite are available to Roomba Pro users,including MAX

Cleaning mode. However, this feature works slightly differently with Roomba Pro,as described below.

• Starting MAX Cleaning with Roomba Pro: If Roomba Pro is off,turn it on (see Feature #1 in Using the Roomba

Remote on page 13),and press the MAX Button on the Roomba Remote.Roomba will play its “Starting a Cleaning Cycle”

tune and begin a MAX cleaning cycle.Roomba typically lets you know what Cleaning Cycle it’s in by illuminating the cor-

responding Cleaning Cycle Button.Since Roomba Pro does not have a MAX Cleaning Cycle Button,no Cleaning Cycle

Button is illuminated while Roomba Pro is in a MAX Cleaning Cycle.

• Pausing MAX Cleaning with Roomba Pro: Once in MAX Cleaning Cycle,you can pause the cleaning cycle in a

variety of ways — pressing the red Pause Button or any Cleaning Cycle Button on the Remote,picking Roomba Pro up or

pressing any Cleaning Cycle Button on Roomba Pro.When Roomba is paused,it typically lets you know what Cleaning

Cycle is paused by flashing the corresponding Cleaning Cycle Button.Since Roomba Pro does not have a MAX Cleaning

Cycle Button,no Cleaning Cycle Button is flashing while Roomba Pro is paused during a MAX Cleaning Cycle.In this

case,Roomba Pro’s control panel may look a bit confusing. Here’s how to tell that Roomba is paused in a MAX Cleaning

Cycle: If none of the Cleaning Cycle buttons are illuminated,and the Battery Indicator Light is not flashing red,then

Roomba is paused in a MAX Cleaning Cycle.

Beyond these two instances,the Roomba Remote will operate the same way it does with Roomba Pro Elite.

The Wall Mount Unit (Roomba Pro Elite only)

The Wall Mount Unit included with Roomba Pro Elite gives you a convenient,compact storage solution for Roomba.The

Wall Mount Unit easily mounts to a variety of wall surfaces,and is designed to provide easy access to empty the Particle

Bin and charge Roomba while stored.All the hardware needed to mount the unit are included with Roomba Pro Elite.The

Wall Mount Unit fits all Roomba and Roomba Pro models,and is available as an accessory.Visit www. RoombaVac.com for

online purchase options,and for more purchase information.

Installing the Wall Mount Unit

To install the Wall Mount Unit you will need a drill,a 1/4”drill bit or 1/8”drill bit (see below to determine which is best for

your needs),a hammer,a pencil,and a #2 Phillips Screwdriver.

1. Remove all protective packing material from around the Wall Mount Unit.

Pro Elite Manual MECH.qxd 7/11/03 11:35 AM Page 15

Irobot roomba pro elite Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info