Bedienungsanleitung Irox EBR505 (Seite 5 von 8) (Englisch)

578594

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

(ENG)

-5-

WIRELESS REMOTE SENSOR REGISTRATION PROCEDURE

1. Insert 3 pieces of AA batteries first to the main unit. The temperature display shows - - - - while the wave icon will keep blinking

for 2 minutes indicate the main unit is in sensor searching mode.

2. In a second step, insert the 2 pieces of AA batteries into the sensor unit. The red LED on the front will start flashing at a rate of

one time per 2 seconds indicates channel-1 is in use.

3. While the red LED is flashing, press once the ▲/CH button (located in the battery compartment) will change the sensor channel

setting to 2. Keep toggle on ▲/CH button can change channel setting up to 3. The LCD is blinking at a frequency to indicate the

channel setting, i.e. continuous blinks 2 times indicate channel-2 is selected.

Note: If user does not press any key for 10 seconds, it will exit the channel setting mode and transmit the RF signal.

The main unit will register the temperature reading.

For later sensor search and registration:

- Start the sending mode on the main unit by pressing the ▲/CH button for 2 seconds.

- On the sensor unit do as described in step 2 and 3 above.

REMOTE CHANNEL AUTO-SCROLLING

This device is equipped with an auto-scroll function. While the auto-scroll function is set, the unit will automatically cycle to display

the temperature and humidity of each remote sensor for 6 seconds.

1. To retrieve manually the specific sensor temperature and humidity reading, press ▲/CH button until desired channel number is

displayed.

2. To enable auto-scroll function, use ▲/CH button to toggle channel 1, 2 or 3 until auto scroll icon appears on the left hand side of

the second line display.

DCF 77 RADIO CONTROLLED CLOCK

The time signal DCF 77 is transmitted by the atomic clock in Mainflingen near Frankfurt/Main. The long-wave transmitter has a range

of up to 1500km.

If the time icon is displayed without waves you have reception problems. Please observe following points:

- There are fewer disturbances in the atmosphere during the night which increases the likeliness of reception. One reception per day

is completely sufficient to ensure the preciseness of the clock by +/- 1 second

- Make sure that the device is at least 2 meters (8 feet) away from possible sources of disturbance such as TV, computer, monitor,

microwave etc.

- In rooms with concrete or metal walls (e.g. cellar rooms, modern office buildings etc.) the receipt of the signal may be more difficult

due to the shielding. In such cases find a better location for the device near a window. Sometimes it also helps to simply turn the

device by 90°, thereby improving the alignment of the receiving antenna.

Once the time signal is received, the wave icon will stay on the LCD, and time and calendar will automatically be updated.

Note: During the 10-minute time signal reception, all manual settings will be suspended. If setting is desired, press once

button key to deactivate the reception. You can also press and hold the same key for 3 seconds to manually

activate the reception in normal mode.

Attention: The radio controlled time signal reception automatically activates itself again within 24 hours.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Irox EBR505 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Irox EBR505

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info