Bedienungsanleitung Irox EBR808C (Seite 21 von 24) (Deutsch, Englisch, Französisch, Italienisch)

578602

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

~P.21~

(ENG)

The light will be activated automatically based on an interval which you can define in the following setting

-Place the slide switch in the position AUTO

-Press and hold the key UNIT for 3 seconds

-With the UP or DOWN key you may set the activation interval in steps ( 5,10,20,30 or 60 minutes)

-To confirm the setting, press the UNIT key again

-Now you can define the sequence of light in the crystal by using the UP/DOWN key:

ON=: each icon will be lit for 1 sec, followed by a full illumination of all icons for 2 secs and then the icon

showing the real weather forecast for 10 secs (18 secs if operated with the adapter).

OF=: whenever the display is activated (manually or interval setting),only the icon for the real weather

forecast will be lit for 12 secs

(Note: Above given timings are approximate numbers only)

GETTING STARTED

This Weather Station was designed for easy set up. For best operation, the following steps are required

to be done in the proper sequence.

1. INSERT BATTERIES FOR MAIN UNIT BEFORE DOING SO FOR THE SENSOR UNITS.

2. RECEIVING UNIT CANNOT BE PROGRAMMED MANUALLY UNTIL THE WIRELESS REMOTE SENSOR

UNIT REGISTRATION PROCEDURE HAS BEEN COMPLETED.

3. POSITION THE REMOTE UNIT AND MAIN UNIT WITHIN EFFECTIVE TRANSMISSION RANGE, WHICH,

IN USUAL CIRCUMSTANCES, IS 250 FEET.

Although the remote unit is weather resistant, it should be placed away from direct sunlight, rain or snow.

BATTERY INSTALLATION FOR MAIN UNIT

1. Turn the metal nut anti-clockwise on the bottom of the unit to open and release the battery compartment;

2. Insert 4 AA size 1.5V alkaline battery as indicate by the polarity;

3. Push the battery compartment back, turn the metal nut clockwise to lock;

Note: Replace the batteries when the low battery indicator appears on the top-right corner of the LCD.

WIRELESS REMOTE SENSOR REGISTRATION PROCEDURE

1. Insert x4 AA batteries first to the main unit, the temperature display shows - - . – While the wave icon

will keep blinking for 2 minutes indicate unit is in sensor searching mode.

2. In a second step, insert the x2 AAA batteries for the sensor unit. The LED on the front panel will start

flashing at a rate of one time per around 2 seconds indicates channel-1 is in use.

3. While the LED is flashing, press once the [CH] key will change the sensor channel setting to 2. Keep

toggle on [CH] key can change channel setting up to 5. The LED is blinking at a frequency to indicate

the channel setting. i.e. continuous blinks 2 times indicate channel-2 is selected.

Note: If user does not press any key for 10 seconds, it will exit the channel setting mode and transmit the

RF signal. The main unit will register the temperature reading.

(If the transmitter has the LCD display, the C/F key will toggle the temperature unit on the LCD.) As the

channel 4 & 5 are reserved for other models, please never set the remote sensor to channel 4 & 5.

REMOTE CHANNEL AUTO-SCROLLING

This device is equipped with an auto-scroll function. While the auto-scroll function is set, the unit will

automatically cycle to display the temperature of each remote sensor for 6 seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Irox EBR808C Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Irox EBR808C

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info