Bedienungsanleitung Iseki TXG237 (Seite 35 von 98) (Englisch)

658894

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

TXG237

BREAK-IN PERIOD

Operation of tractor within the first 50h can be a major

factor in determining the performance and life of the

engine and Tractor:

・

The engine may be operated at full rpm but exces-

sive load should be avoided. If engine begins to

“lug”,operate in a lower gear to maintain higher

enginespeed.

・

Check coolant level and check engine, transmis-

sion and other oil levels frequently during break-in

period.

Watch for evidence of leakage of above fluids.

Replenish levels as required and repair any leaks

that may have formed.

・

Tighten any nuts, bolts, or screws that may have

loosened and retighten as necessary. This is espe

cially true of wheel retaining bolts. All fasteners on

this Tractor are metric.

・

Be observant of clutch and brake pedal free-play

adjustments and readjust as required. Lining materi-

als used in clutch disc and brake shoes “bed in” the

first few hours of operation and may necessitate the

need for early and frequent readjustment.

・

Keep area around fuel tank filler clean. Make

sure diesel fuel is of correct grade and free of

contamination.

・

Initial engine oil and oil filter change is after first 50h

of operation. Subsequent change interval is every

150h for engine oil and filter.

CAUTION: Proper maintenance practices

cannot be over-emphasized. They are

required for safe operation. Consultant

“Lubrication and Maintenance” section

for full details.

OPERATION

STARTING

Pre-Start Inspection

Prior to daily start-up of Tractor, a few basic proce-

dures should be followed to ensure Tractor is in oper-

ating order to insure longer life and dependability:

・

Make sure all safety shields are in place and se-

cured properly.

・

Make sure operator is instructed in correct and

safe peration of Tractor and related attachments or

implements.

・

Check coolant, engine oil and transmission oil lev-

els and replenish as necessary.

・

Check fan belt tension and adjust as required.

・

Make sure radiator, air intake screen, and radiator

screen are clear of debris to provide maximum en-

gine cooling.

・

Check operation of clutch, brake and throttle controls.

All controls must operate freely and be adjusted correctly.

・

Conduct a general inspection of tires, tire pressure,

and wheel bolt torque. Observe for external signs of

leakage and correct before operating Tractor. Check

steering for excessive looseness.

・

Check for adequate fuel supply. If is recommended

fuel tank be filled following each days use to; reduce

condensation and provide full tank for next use.

・

Check operation of lights and warning flashers. If

Tractor is to be transported on public road, ensure

slow moving vehicle emblem is in place.

NOTE: Requirements may vary regarding use of warn-

ing flashers and slow moving vehicle emblem

depending on locality. Check local safety codes.

WARNING: Carefully read and understand

the SAFETY section of this book. Your

life, and that of others, can be in danger

during the starting of the Tractor.

Always start and operate the engine in a

well ventilated area.

If in an enclosed area, vent the exhaust to

the outside.

DO NOT modify or tamper with the ex-

haust system.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Iseki TXG237 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info