Bedienungsanleitung Jablotron AS-80 (Seite 2 von 4) (Englisch)

555055

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

AS-80 access system control unit MKM51600

• If you have a JA-80N proximity reader, present the RFID card 10

times and when the reader performs a confirmation double-beep,

present the card 10 times again

5. After setting master or slave operation mode the reader will exit

setting automatically

6. Disconnect the power, re-connect the DTA terminal (brown) wire

and restore the power

Note: Further system programming can only be done on the master

keypad.

2. On the master keypad set the service and master card and/or code

as follows:

1. Disconnect the power

2. Disconnect the CLK terminal (Green wire) and connect it to the

yellow wire

3. Restore the power

4. After the reader starts sounding, disconnect the green and yellow wires

5. Choose master code or master card

a) Enter the new master code (3 to 6 digits) and press # # (only code)

b) Or press # and present the card (only card)

c) Or enter the new master code (3 to 6 digits) and press #,

present master card or press # again.

6. Choose service code or service card

a) Enter the new service code (3 to 6 digits) and press # # (only code)

b) Or press # and present the card (only card)

c) Or enter new service code (3 to 6 digits) and press #, present

the service card or press # again

7. Disconnect the power, connect the CLK (Green wire) wire back

and restore the power

Note: If the master or service code is forgotten or the card is lost, then by

this procedure it is possible to perform a factory default reset of the

keypad

The master and service code/card can only be used for programming

the system - it cannot be used for system operation.

Service mode

Enter service code or use the service card. The OPEN LED and

STATUS

LED light green (service mode).

To program any optional parameters always press all 13 digits C1 to

C13 according to following table. After entering the last digit the reader

saves all the data, and exits programming mode automatically.

Note: If you don’t press a key within 20 seconds, service mode will be

exited without saving any data.

Parameter Value Description Default

C1 and C2 00–99

C1 and C2 is a period of time during which the relay set as the Door lock is switched on (01 – 99 sec.). If 00 is

entered, then the output will be set to a latch mode (it toggles its status whenever a valid assigned code or card is

entered).

4 sec

C3 and C4 00

No meaning, enter 00

C5 0,4,6,7

RELAY 1 output reaction:

[0] – Off = no reaction

[4] – Door lock = switched on for a time specified in parameters C1-C2 when a correct code / card is entered

[6] – Tamper alarm = after 3 unsuccessful attempts at entering a code or card the output will produce a 4 second

long pulse

[7] – Door bell = whenever the F1 or F2 key on the keypad is pressed, the output will produce a 5 second long

pulse

Door lock

C6 0,4,6,7 RELAY 2 output reaction – setting parameters are the same as for RELAY 1

C7 0

No meaning, enter 0

C8 0 – 2

Function settings for IN:

[0] – Off = no reaction

[2] – Exit button switch = connecting IN to GND will have the same effect as entering a valid user code

Exit

button

switch

C9 0

No meaning, enter 0

C10 0 – 1

The access mode for the master keypad:

[0] - Card or Code

[1] - Card and Code

Card or

Code

C11 0 – 1

The access mode for the slave keypad / reader:

[0] - Card or Code

[1] - Card and Code

Card or

Code

C12 0 – 1

Tamper alarm indicated by an internal buzzer

[0] – Disabled

[1] – Enabled

Disabled

C13 0

No meaning, enter 0

Configuration parameters in service mode

Example: by entering 0200460200100 you will set – Door unlock time 2 seconds, RELAY1 reaction Door lock, RELAY2 reaction tamper alarm, IN

reaction exit button switch, master keypad access Card or Code, slave keypad access Card and Code, Alarm indicated by buzzer disabled.

Access code setting

120 different access codes and/or cards can be used. The factory

default codes are blank. All access codes can have from 3 to 6 digits.

Enter the master code or use the master card. The OPEN

LED and

STATUS

LED are lit (access code setting mode).

• Setting access codes and RFID cards:

Use the sequence 3 ID CODE # Card

Where: ID is a user number (from 000 to 119)

CODE is a new code (3 to 6 digits), after pressing # present

the RFID card which will be assigned to the same

user position. If the card is not required, press the #

button again.

• Deleting user codes and RFID cards:

Use the sequence 9 ID

Where: ID is a user number (from 000 to 119)

• Delete all access code / cards

Use the sequence * 0

To exit, press the # key

Note:

- If you assign a new user code to an ID that is already occupied by

some other user, the original code will be deleted.

- Any attempt to program an already registered card or code will be

indicated as a programming error.

- If no button is pressed for 20 seconds the current sequence will be

terminated. If no button is pressed for 150 seconds then setting mode

will be exited.

Operation

By entering a proper access code followed by the # key and/or

presenting an RFID card, the output set as Door lock will be switched

on for a set period of time (confirmed by 3 short beeps). If the latch

mode has been set, then every proper code entry will toggle the status of

the output – ON-OFF-ON-.

Whether the RFID card must be followed by the code or not can be set

separately for master and slave keypads. Therefore, for example, for a

higher level of security, to enter the premises both a card and code could

be required, and to leave the premises only a card or code could be

required.

Jablotron AS-80 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info