554915
18
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
MLO51201 - 18 -
System extension
Individually bought devices should be enrolled to Azor using a registration code. The code
consists of ten digits and it is in the following format: 123-4567-890. Enrollment (or removal)
of a device is performed with a computer. The registration code can be filled into the Serial
Number box on the Detectors page. If the registration code is unknown (e.g. damaged label)
please use A-Link. Choose the wanted field for enrolling the device and click the Enroll
button. Insert the battery into the device. As a confirmation of successfull enrollment the
registration code is displayed in the field.
AZ-10T RFID tag
There is a sticker with a registration code on a new RFID tag. If the RFID tag code is no
longer legible, please use the RFID tag reader and A-Link software for enrolling it. Choose
the Tag number field in the Users window and click the Enroll button. The code is enrolled
after pressing SET on the AT-10D RFID tag reader and scanning the RFID tag. As a
confirmation of successfull enrollment the registration code is displayed in the field.
Note: Azor uses special security RFID tags. No other RFID tags can be enrolled to it.
AZ-10M door-opening detector
Besides detecting door and window opening, the detector can also report e.g. the
movement of objects etc. You can also connect an external sensor to it.
Terminals:
INPUT serves for connecting external alarm sensors. When the GROUND terminal is
disconnected an alarm signal is sent (identical to that of reporting door
opening).
TAMPER serves for connecting external tamper sensors. When the GROUND terminal
is disconnected a tamper signal is sent (identical to that of reporting detector
opening).
GROUND common terminal. If the INPUT or TAMPER terminal is not used, it must be
permanently connected to this terminal.
Internal switches:
1 DEL the detector provides an entrance delay*
INST the detector does not provide an entrance delay*
2 MG EN the built-in magnetic sensor is enabled
MG DIS the built-in magnetic sensor is disabled (only INPUT terminal activation is
reported)
*) applies only if a “default” reaction is set for the detector
Battery-low signalling
When the detector batteries are low, Azor sends an informative message. Besides that the
detector LED flashes when you open the door (outside test mode).
18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Jablotron AZK PLUS-EX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info