Bedienungsanleitung Jablotron BM-01 Nanny (Seite 2 von 2) (Englisch)

555044

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Baby monitor BM-01A “Nanny“ 2/4 MFV51303 Baby monitor BM-01A “Nanny“ 3/4 MFV51303

Installation

1. Place the sensor pad on the bed bottom as shown in the diagram. Place

the mattress on the sensor pad and be sure that the sensor is well positioned

with the mattress using the following guidelines:

• Center of the sensor pad should be approximately in the position of where the

baby’s chest will be

• Pad should be on a smooth & solid surface – It should not be bent!!.

• If there is only a spring grid supporting the bed, place a solid board (wood,

plywood etc.) between the pad and the spring grid.

• If you want to use the Nanny in multiple beds, use extra sensor pads (item number

BM-01D). Install them in each bed and change only the location of the control unit.

• Up to two sensor pads can be used in each bed with a single control unit if the

child is large.

Connecting batteries to the control unit (battery compartment is on the rear

side of the control unit):

• Use only 2 new size AA alkaline batteries.

• Polarity of the batteries is clearly marked in the battery compartment.

• Close the battery cover and turn the switch to position I.

• If the batteries are OK, you will hear a beep and the indicators will flash.

• Switch the unit OFF again (position 0)

• If there is no beep after turning ON, check the batteries.

Attaching the control unit to the bed – using the fastening belt

• The unit should be visible and should not by covered by anything

• For bigger children we recommend to locate the unit out of their reach

4. Connecting the sensor’s cable to the unit – you should hear a click

• Route the cable in such a way that there is no slack long enough to make a loop.

For bigger children the cable should be out of their reach

• If you do not use the entire length of the cable, fix the excess firmly under the

mattress.

• If you position the control unit in another room, use the extension cable (5m),

which is provided with the set. Only one extension cable can be used.

• If you use two sensor pads in a bed, a cable splitter is provided in the set.

• To disconnect the cable from the unit – press the connector tab towards the cable

Switch and Indicators

Switch – position 0 = OFF, I = ON

Red indicator – flashing when there is an ALARM

Green indicator – a short flash indicates a breath or a movement of the baby

Yellow indicator – flashing indicates low batteries

Operation

A. Put the baby to bed.

B. Turn on the unit (confirmed by a beep and a flash of all LED indicators)

C. The green led indicator will flashes as the baby breathes or moves

D. Turn off the unit before you take the baby out of the bed.

ALARM

If the baby is not breathing for longer than 20 seconds, or the breath rate is too slow, an

alarm signal will sound and the red indicator will flash.

Check the baby and provide first aid if necessary

(make sure that there are no reasons

for choking, start resuscitation, call for emergency help). In some cases of Apnea the sound of

the unit itself can wake the baby up and he/she will start to breath again on his/her own.

Alarm can be stopped by the switching the unit off.

There may be rare cases of false alarms, especially when the child is crawling and moves

off the sensor pad.

Testing

You can test function of the Nanny in the following way (should be tested once a week):

1. If the baby is in the bed and the unit is ON, the green indicator should flash as the

baby is breathing or moving.

2. Leave the unit ON and take the baby out of the bed.

• The green indicator may continue to blink for a certain time (vibrations of

the bed caused by the baby’s removal)

• Do not hold or touch the bed – the device may detect your breathing

3. When the flashing has stopped for 20 seconds, the unit will make warning beeps and will

start the alarm sound

• The red indicator should flash when the alarm is triggered.

• Stop alarm by turning the switch on the unit OFF.

If the device does not work as described above, check that:

• There is a beep after switching it on. If not, check the batteries.

• After taking the baby out of the bed the green indicator stops flashing (within a

minute or so) – if not, the device is detecting some intrusive vibrations – see

following warning.

Important warning:

• The Nanny is a very sensitive instrument, capable of sensing a sleeping baby’s

breathing. Intrusive vibrations of the bed, the floor or the entire building can influence

its performance. The bed should not be in physical contact with another bed (which

is used by another person or animal) or with any device that generates vibrations.

Intrusive vibrations can also be caused by a powerful air movement (fan, air-

conditioning…), by walking close the bed and by other sources. If you move the bed

to a new location, you should test the Nanny before you use it.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Jablotron BM-01 Nanny Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info