GSM autoalarm CA-1202 „Athos“ 2/4 MHF52505
Figure 1: installation of the car alarm in Mode 1
6.1 Programming sequences
Enter the prescribed spaces in SMS texts as shown in the table below. MASTER is a factory default master code, which should be changed to your own
password. All SMS texts are case insensitive.
SIM entry* Text of SMS instruction Descrip tion
RESET 1 MASTER RESET EN 1 Mode setting. Factory default is 0 – no function (imm o b il i z a t io n r el a y co p i es i g n it i o n) . Note: By
performing the RESET EN x instruction, all settings, remote controllers and enrolled wireless dete ctors
will be erased! RESET is indicated by four siren chirps.
Not possible MASTER UC uuuu
User Code setting – the code (password) allows you to operate the alarm remotely via SMS from
unauthorized phones. uuuu is a new user code, u p to 8 letters (A –Z & 0 – 9). Factory default user
code is USER
Not possible MASTER MC xxxx Master Code setting, xxxx is a new master code, up to 8 characters (A –Z & 0 – 9).
The code allows you to change settings for the car alarm. Factory default master code is MASTER
TEL1 xx...x M ASTER TEL1 xx...x
TEL2 xx...x M ASTER TEL2 xx...x
TEL3 xx...x M ASTER TEL3 xx...x
TEL4 xx...x M ASTER TEL4 xx...x
Setting of phone numbers to re port alarms (these phones will also be auth orized to control the
alarm via SMS without a user password)
E.g.: MASTER TEL2 +420602123456 will enter the phone number to TEL2 memory
MASTER TEL3 0 will erase the TEL3 memory.
DIAL1 xx...x M ASTER DIAL1 xx...x
DIAL2 xx...x M ASTER DIAL2 xx...x
DIALA xx...x MASTER DIALA xx...x
DIALB xx...x MASTER DIALB xx...x
Setting of phone numbers to dial using Hands free.
E.g.: MASTER DIAL2 +420602123456 will enter the number to DIAL2 memory (which is dialed after
you press button 2 on the remote control)
MASTER DIAL2 0 will erase the memory DIAL2.
DIP abcdefghij MASTER DIP abcdefghij DIP parameters entry – see part 7
SET abcdefghi M ASTER SET abcdefghi SET parameters entry – see part 8
Not possible MASTER LEARN RC Remote Control enrollmen t - up to 4 controllers can be enrolled, turn the ignition key on before
sending the instruction. To enroll a remote control press and hold buttons A and B together for 3
seconds. After you enroll all remote controls, turn the ignition key off.
Not possible MASTER LEARN JA JA-60 wireless detector enrollment – up to 8 detectors can be enrolled, turn the ignition key on
before sending the instruction. To enroll a detector insert its battery. After you enroll all detectors, turn
the ignition key off.
Not possible
MASTER TXT 01,text Editing of SMS texts (reports and instructions), see part 10
TELU xx...x MASTER TELU xx...x Sustained call setting (for pre-paid cards) 1x mont h the xx..x number is called, call duration 10 s.
* See part 5 for details.
GSM car alarm CA-1202 „Athos“ 3/4 MHF52505
7 DIP parameters
By SMS: MASTER D IP A BCDEFG HIJ you can change 10 features:
Description
DIP
0 1
A 0 = Silent arming/disarming without si ren chirps
1 = 10 ms sire n chirps when arming/disarming (non backe d-up siren)
2 = 20 ms siren chirps when arming/disarming (bac ked-up siren)
B Silent alarm
Audible alarm (30 sec.)
C
SMS alarm report only
SMS alarm report + sire n sound
phone call
D SMS remote contr ol not
confirmed by SMS reply
SMS remote con trol instruc tions
confirmed by SMS repl y
E
0 = arming contro l by dialing in from T EL1 to T EL4 disab led
1 = arming control by dialing from TEL 1 enabled
2 = arming contr ol by dialing from TEL1 and TEL2 enab led
3 = arming contr ol by dialing from TEL1, TEL2 and TEL3 enabled
4 = arming contr ol by dialing from all TEL1 to TEL4 enabled
Arming and disarming by dialing from au thorized phones is free of charg e
F
Arming control by dialing
in is not confirmed by
SMS
Arming contr ol by dialin g in (se e E) is
confir med by SMS to the phone whi ch
dialed the car alarm
G
User can not cha nge SMS
texts
User can chan ge SMS texts by TXT
sequence
H
REARM disabled
If the car i s not enter ed within 1
minute after disar ming, it will REARM
I
0 = Immob ilizatio n by arming and by SMS in struct ion
1 = Immobilization by arming and automatica lly 5 minutes after ignition is
turned off and also by SMS instruction
2 = Immobilizati on only by SMS instruction
J
Self-location disabled
The car´s lo cation w ill be sent by SMS
to all TEL1 t o TEL4 if th ere is an alarm
or if the c ar stops afte r immobiliz ation
SMS instruc tion (See 13. 6.)
Factory default setting is DIP 1111000000 (bold letters in the text). If you
want to change only particular parameters, enter x for the others (i.e.
MASTER DIP 0xxxxxxxxx will make arm ing control silent).
8 SET parameters
By SMS: MASTER SET ABCDEFGHI you can change 9 features:
Description
SET
0 1
A
Open door arm ing ind ication
disabled
Audible indication of arming
with open door (4 beeps)
B
Voltage detect or disabled
Voltage drop detector enabled
C
lock / unl ock signal durat ion
0 = 0,3 / 0,3 s ec
1 = 4 / 4 sec
2 = 60 / 0,3 se c (aut omatic wind ow closi ng)
D
DOOR input logic:
0 = automa tic
1 = activated b y falling edge (grounding)
2 = activated b y rising edge (disconnecting from GND)
E INP1 logic:
0 = automa tic
1 = activated b y falling edge (grounding)
2 = activated b y rising edge (disconnecting from GND)
F INP2 l ogic:
0 = automa tic
1 = activated b y falling edge (grounding)
2 = activated b y rising edge (disconnecting from GND)
G no function in Mo de1
H no function in Mode1
I no function in Mode1
Factory default setting SET 100000010 (bold letters in the text).
If you want to change only particular parameters, enter x for the others
(i.e. MASTER SET 0xxxxxxxx will disable open door arming indication).
9 User instructions
9.1 Remote control armin g and disarming
Button A of the remote control is used for arm ing, B for disarming (arming
control is confirm ed by a siren chirp) .
9.2 Remote control by SMS instructions
SMS instructions sent from an authorized phone (TEL1 to TEL4) can
operate the alarm remotely. Factory default instruction texts are shown in
the following table. The instruction texts can be changed by SMS text
editing, see part 10.
If an SMS is sent from an una uthorized phone (o ther than TEL1 to TEL4), a
valid user code must be en tered before the in struction (e.g. USER IMO) .
SMS text Description
AM
ARM and lock t he car
DM
DISARM and u nlock the c ar
IMO
STOP (immobilize) the ca r (after tu rning the ig nition key off)
UNIMO
Unblock (mobi lize) t he car
STAT US
Car alarm w ill reply with status information, e.g. „car reports:
Time: 27.01.0 4 13:04, Stat us: Armed, U nblocked, I gnition
off“.
HELP
The car alarm w ill reply with a brief l ist of SMS instr uctions.
UC uuuu
To change th e user code. uuuu is the new user code, up to 8
characters (A –Z & 0 – 9). Fac tory default user code is
USER
CREDIT
To obtain the balance of a prepai d SIM card if used. See 13.7
for details
HF abcdef
Hands-free s et adj ustment:
a – enable cal ls (0= disabled , 1=enabled)
b – auto an swer incomi ng calls (0= disabled , 1=enabled)
c – micropho ne sensitiv ity 0 to 9, (5)
d – speaker volume 0 to 9, (5)
e - ringing t one volum e 0=mute to 9= max., (5)
f – ringing sound 0 to 9, (5)
LOCATOR
To obtain the car locatio n from the GSM provider. See 13.6
for details.
• The parameters in bold are factory defaults.
• The instruction must contain spaces as sho wn in the table
• Only basic ASCII can be used in the SMS instruction texts
• If the SMS text contains the % sign, then the following text will be
ignored. Characters %% in the message stop processin g the
following text. Using these characters is suitable when send ing an
SMS from an internet gateway which ads another text –
advertisements etc. When using the % character it is alwa ys
necessary to insert the Master or User code followed by a space
before the command itself.
9.3 Internet remote control
After you register the alarm on the www.GS ML in k.c z
web site (see 11),
you can access your alarm remotely from the internet. Using this a ccess
you can obtain the status of your car, you can arm, disarm and you can
also stop the car after it was stolen. It is also possible to view the memory
of the alarm. Installers can change the settings of the alarm remotely
using the internet access.
9.3 Dialing-in remote control
If enabled by the DIP parameters (see 7), the car alarm can be armed
and disarmed remotely by dialing in from an authorized phone (TEL1 to
TEL4). The car alarm will not answer the incoming call, but when it
recognizes your number, it will change status (Arm or Disarm).
Such remote control is free of charge since the phone is not answered.
Warning – if you dial your car alarm a ccidentally it can cause
disarming of the alarm.
9.5 Phone calls by installed hands free set
If the optional HF-03 hands free set is installed, it is possible to receive
and make phone calls via the car alarm. When your car is disarmed an d
ignition key is on, th e remote control (RC-40) allows you to operate the
hands free set.
Incoming calls – to answer them, press any button on the RC-40 remote
control. By pressing any button again, the call w ill be terminated.
Whe n armed, all incoming cal ls are automatically rejected. If the car is
blocked (by IMO instruction) all calls are automatically answered (it is
possible to listen and to speak to the car remotely). Automatic call
answering while you are driving can also be enabled by the HF
instruction (see 9.2).
To make a call – y ou can call up to 4 preprogram med numbers while y ou are
driving. By pressing butt on A, B, 1 or 2 on th e remote cont rol you will dial the
corresponding number (pre programmed by DIALA to DIAL2, see 6.1)
9.6 Alarm
When an alarm is triggered, t he siren will sound for 30 sec., w arning SMS
messages will be s ent to all phones (TEL1 to TEL4) and these phones will
also be called wit h the siren sound.
To stop the alarm, disarm the alarm by pressing the B button on the
remote control or by disarm SMS instruction (DM).
10 S MS text editing
The SMS texts (alarm information and instructions) are factory
preprogrammed. However, it is possible to change these texts by a
mobile phone or via internet access www.GSMlink.cz
To change a text by your mobile phone, send SMS: