GSM car alarm CA-1802 „Athos“ 4/6 MHF57202
Factory default setting is SET 1001111101 (bold letters in the text).
If you want to cha
others (i.e.
MASTER SET xx2xxxxxxx will
closing the windows).
8. User instructions
8.1. Remo
Button
is used to arm and
button the car can be disarmed and un
button within 15 second
acoustically). In t
nor is the low voltage
sensors. Using the CR-11A module, pressing t
and
together allows y
independent heating).
8.2. SMS contr
Text SMS Description
AM
ARM and lock the
AM EXT
Partially ARM and lock
DM
DISARM and unl
IMO
STOP (immobilize) the car (
UNIMO
Unblock (
STATUS
Car alarm will re„ca
reports: Time:
Ignition off“.
HELP
The car alarm will
UC xxxx
To change thxxxx is the new user co
characters (A
USER
CREDIT
parameter
To obtain the
12.6-8 for
AUX
parameter
To operate CR
or circuits th
HF abcdef
Hands-free s
a – enable ca0= disabled , 1=enabled)
b – auto an0= disabled , 1=enable
c – microphone(5)
d – speaker v (5)
e - ringing to(5)
f – ringing sound 0 to 9, (1)
SIREN
To activate the
The instruction must contain spaces (
If an SMS instructunauthorized phone , it is
necessary to put a user code befor
Again, a space is nece
unauthorized phone: USER AM
SMS instruct
used in the SMS instruction texts.
If the SMS tex then the following text will be
ignored. Characters %% in the message stop processing the
following text. Using these characters is suitable when sending an
SMS from an internet gateway
advertisements etc. When using the % character it is alw
necessary to insert the Master or User code followed by a space
before the command itself.
SMS instruct
“AM“ by “LOCK“.
The parameters in bold are factory defaults.
8.3. Dialling
Complete remote control by
possible (see table DIP – para
from an authorized phone, it w
di
an
been triggered, a
partial arming, th
Change of state after d
8.4. Phone
If the HF-03 hands free set is installed, it is possible to receive ca
and to dial pre-programmed phone numbers DIAL x. When
ignition key is on, the remote control (RC-8
the hands free set. The call is done via the car alarm’s SIM, the
handsfree set is not usable for other phones.
Incoming calls – to answer them, press any button on the RC-8x
remote control. By pressing any button aga
terminated.
Calls can be automatically answered, see the HF instruction manual.
Outgoing calls – when the ignition key is on, the RC-8x allows you
to
When armed, all incoming calls are automatically rejected. If the car
is immobilized or after an alarm has been
automatically answered (it is possible to listen in).
8.5. Alarm
When an alarm is triggered, the siren will so
SMS messages w
phones will also be ca
turned on, a request for locatio
alarm, all transmissions are term
To stop the aladisarm th
button on
the remote control or by a disarm SMS instruction (DM). The DM
instruction unlocks the car at the same time. After the alarm has been
stopped by a user in a regular way, an SMS will be sent informing
about alarm termination.
Example of an alarm SMS:
Your car reports: A
Mercedes repo
01:12
8.6. Acoustic signalling of arming/disarming
If acoustic signalling is ON (see table 6), the arming is confirmed by
1 beep and disarming by 2 beeps. Partial arming is indicated by two
short beeps. Three beeps while disarming the
alarm was triggered during the armed state. If arming a car
active alarm input (e.g. open car boot) arming is supplemented by four
short beeps. The siren will also indicate triggering of a wireless
detector which provides an entrance delay (by a single beep).
9. Editing SMS texts
The SMS texts (alarm information and instructions) are factory pre-
programmed. However, it is possible to change these texts using a
mobile phone or via the www.GSMLink.cz
internet page. This makes
communication convenient for the user.
To change text by mobile phone, send an SMS as below. A single
SMS enables you to specify changes to several texts. Terminate each
text with a comma:
MASTER TXT zz,text,zz,text,…
where: zz is the text index
text is y
or comma cannot be used in the text, spaces are
allowed
Example: MASTER TXT 01,LOCK PLEASE
Text numbers 01 to 26 are instructions requiring a
their modification. If you modify these t
instructions which the car alarm will respond to. For example, replacing
“STATUS” with “STATE PASSWORD” will cause that state detection
will be obtainable by “STATE PASSWORD” only. This way you can
insert a “password” into the te
texts are of informational character and corr
events, states and input names. This allows you to adjust the names to
a form which suits you well. For example, “INP 1” can be replaced with
“bonnet” etc. Texts can be replaced using the MASTER code as
as the USER code (optional).
A convenient way for text modification is to use the GSMLink web
page, see paragraph 11.
SMS text table
zz Fact zz Fact
SMS commands: 48 Telephone
01 AM 49 Telephone
02 DM 50 Telephone – MC
03 IMO 51 Wireless detector 1
04 UNIMO 52 Wireless detector 2
05 STATUS 53 Wireless detector 3
06 HELP 54 Wireless detector 4
07 CREDIT 55 Wireless detector 5
08 DIAL 56 Wireless detector 6
09 HF 57 Wireless detector 7
10 LOCATOR 58 Wireless detector 8
11 MC 59 Wireless controller 1
12 UC 60 Wireless controller 2
13 DIP 61 Wireless controller 3
14 TEL 62 Wireless controller 4
15 LEARN Status information:
16 SIREN 64 Car
17 SET 65 Status:
18 AUXA 66 Armed
19 AUXB 67 Disarmed
25 ON 68 Ignition
26 OFF 69 Ignition
Even 70 Engine is blocked
30 Alarm 71 Engine is unblocked
