Bedienungsanleitung Jablotron CA-1802 - Athos GSM RESET 3 (Seite 4 von 5) (Englisch)

555042

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

GSM pager CA-1802 „Athos“ 4/5 MHF57402

SMS from an internet gateway which adds more text –

advertisements etc. When using the % character it is always

necessary to insert the Master or User code followed by a space

before the command itself.

 SMS instructions can be renamed. Example: It is possible to replace

“IMO“ by “BLOCK“.

 The parameters in bold are factory defaults.

8.1. Phone calls by handsfree set (HF-03)

If the HF-03 hands free set is installed, it is possible to receive calls

and to dial pre-programmed phone numbers DIAL x. When the ignition

key is on, an RC-8x allows you to operate the hands free set. A voltage

of +12V is required on the ignition key input when a call starts or ends.

The call is done via the car alarm’s SIM, the handsfree set is not usable

for other phones.

Incoming calls – to answer them, press any button on the RC-8x

remote control. By pressing any button again, the call will be terminated.

Calls can be automatically answered, see the HF instruction manual.

Outgoing calls – when the ignition key is on (i.e. when a voltage of

+12V is present on its input), the RC-8x allows you to call up to 4 pre-

programmed numbers (see the configuration table).

If the ignition key is off (i.e. no voltage of +12V is present on its input),

all incoming calls are automatically rejected. If the car is immobilized all

calls are automatically answered (it is possible to listen in).

8.2. Alarm

When an alarm is triggered, the siren output will be switched on for 30

sec., warning SMS messages will be sent to all phones (TEL1 to TEL4).

Subsequently, these phones will also be called by the GSM pager. If

automatic location is turned on, a request for location detection is sent.

The LED indicates the alarm for 2 minutes. To activate inputs

subsequently, an interval of at least two minutes is required.

To stop the alarm, disarm the alarm by pressing the

button on the

remote control.

Example of an alarm SMS:

Your car reports: Alarm, INP activation, Time 10.12.04 01:45

9. Editing SMS texts

The SMS texts (alarm information and instructions) are factory pre-

programmed. However, it is possible to change these texts using a

mobile phone or via the www.GSMLink.cz

internet page. This makes

communication convenient for the user.

To change text by mobile phone, send an SMS as below. A single

SMS enables you to specify changes to several texts. Terminate each

text with a comma:

MASTER TXT zz,text,zz,text,…

where: zz is the text index (see following table)

text is your new text – up to 30 characters, full stop (dot) or

comma cannot be used in the text, spaces are allowed

Example: MASTER TXT 03,BLOCK PLEASE

Text numbers 01 to 26 are instructions requiring a MASTER code for

their modification. If you modify these texts, you change the instructions

which the GSM pager will respond to. For example, replacing “STATUS”

with “STATE PASSWORD” will cause state detection to be only

obtainable by “STATE PASSWORD”. This way you can insert a

“password” into the texts which prevents misuse. All other texts are of

informational character and correspond to particular events, states and

input names. This allows you to adjust the names to a form which suits

you well. For example, “INP 1” can be replaced with “bonnet” etc. Texts

can be replaced using the MASTER code as well as the USER code

(optional).

A convenient way for text modification is to use the GSMLink web

page.

SMS text table

Zz Factory default text zz Factory default text

SMS commands: 48 Telephone 4

01 AM 49 Telephone - UC

02 DM 50 Telephone - MC

03 IMO 51 Wireless detector 1

04 UNIMO 52 Wireless detector 2

05 STATUS 53 Wireless detector 3

06 HELP 54 Wireless detector 4

07 CREDIT 55 Wireless detector 5

08 DIAL 56 Wireless detector 6

09 HF 57 Wireless detector 7

10 LOCATOR 58 Wireless detector 8

11 MC 59 Wireless controller 1

12 UC 60 Wireless controller 2

13 DIP 61 Wireless controller 3

14 TEL 62 Wireless controller 4

15 LEARN Status information:

16 SIREN 64 Car alarm reports

17 SET 65 Status:

18 AUXA 66 Armed

19 AUXB 67 Disarmed

25 ON 68 Ignition key ON

26 OFF 69 Ignition key OFF

Events: 70 Engine is blocked

30 Alarm 71 Engine is unblocked

31 Alarm cancelled by a user 72 No alarm

32 Fire alarm 73 Alarm timeout

33 Tamper alarm 74 Low battery voltage

34 Disarming 75 Power failure

35 Arming 76 Power recovery

36 Low battery voltage 77 Time

37 Engine is blocked 79 Partially

38 Engine is unblocked Confirmation SMS:

Source:

81 Command accepted

40 Ignition key 82 Command syntax error

41 Door contact 83 New MC code:

42 INP1 activation 84 New UC code:

43 INP2 activation 85 Reset

44 Low battery voltage sensor 86 Registered phone number:

45 Telephone 1 87 Credit:

46 Telephone 2 88 LEARN mode, enrolled

47 Telephone 3

The grey-tinted items are not available for RESET 3 mode. Use only

ASCII character set during the text editing.

10. Internet remote access

The web site www.GSMLink.cz enables remote control (to users) and

setting (to installers) of the GSM pager.

To get internet access to an installed and powered car alarm you will

first be asked to register your car alarm on the first page. You will find a

unique registration code for your car alarm on the warranty card.

11. Central monitoring station communication

The GSM communicator allows central monitoring via GPRS data

protocol. The central monitoring station (CMS) gets arming, disarming and

alarm information. It also regularly checks the communication link to the car

after it is armed. So if anyone tries to tamper with GSM communications, it

will indicate an alarm at the CMS.

12. Additional features

12.1. Remote siren activation

You can operate the siren remotely by the SIREN instructions. These

instructions are accepted from all authorized (stored) phone numbers.

Commands are also accepted from any unknown phone number if they start

with the USER code.

Instruction Status

SIREN ON activates SIR output permanently

SIREN OFF deactivate SIR output

SIREN activates SIR output for 30 sec.

SIREN xxM

SIREN xxxS

xxM – is the numeric value of the

duration of SIR output activation, in

minutes

xxxS – as above, but in seconds.

LED indicator signals

LED state Meaning

OFF Disarmed

permanently ON Connecting to a GSM network or a phone call

Regular fast flashing

Alarm or an alarm memory or learn mode

Interrupted light Car was stopped (immobilization)

Flashing after ignition off GSM network is not available

Flashes after ignition on Number of enrolled remote controls

12.2. Pre-paid SIM card balance

It is recommended not to use prepaid cards in the car alarm. If you

have no other choice than prepaid cards, you can enable the CREDIT

instruction by the following sequence:

MASTER CREDIT uuu..u xx yyy zz

where: uuu…u is the provider’s code to obtain the balance

xx is the time period (in days) for regular checking

yyy is the threshold level below which the balance is

reported to the user (TEL1)

zz is the position of the first digit of the balance in the reply

SMS from the provider

Jablotron CA-1802 - Athos GSM RESET 3 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Jablotron CA-1802 - Athos GSM RESET 3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info