GSM pager CA-1803BT „Athos“ 5/6 MHF56803
10.2. Time
To adjust the time information to local time, time zone setting is
possible. The car alarm adds/subtracts the time shift, expressed in
hours, to the GMT time (for
hour in winter time). This instruction is only available with the MASTER
code.
Instruction: MASTER TIME ±xy
xy is the time shift in hours -3,-2 …+1,+2 relative to GMT
`
MASTER TIME GSM
turns on automatic setting via incoming SMS.
10.3.
A Bluetooth module is supp
alarm. The module allows
equipped with Bluetooth
mobile phones, such com
running on these devices. When d
car alarm sends GPS coordinates via the BT which can be use
navigation. The car alar
ignition key must
If the car stands still for more than 10 minutes, GPS data transmission
may start with a delay of up to 1 minute.
11. Internet remote acces
The web site www.GSMLink.cz enables remote control (t
setting (to installers) of the GSM pager.
To get internet access to an installed and powered car alarm you
first be asked to register your car alarm on the first page. You will fi
unique registration code for your car alarm on t
12. Central monitoring station communication
The GSM communicator allows cen
protocol. The central mon
alarm information. It also re
after it is armed. So if anyone trie
will indicat
13. Additional
13.1. Re
You can operate the
instructionl authorized (stored) phone numbers.
Commands are also acce
with the USER code.
Instruction Status
SIREN ON activates SIR output permanently
SIREN OFF deactivate SIR output
SIREN activates SIR output for 30 sec.
SIREN xxM
or
SIREN xxxS
xxM – is a numeric value of the
duration of SIR output activation, in
minutes
xxxS – as above, but in seconds.
13.2. LE
LED state Meaning
OFF Disarmed
permanently ON Connecting to a GSM netw
Regular fast flashing
Alarm or an
Interrupted light Car was stopped (immobilization)
Flashing after igniti GSM ne
Flashes after ignition on Number of enrolled remote
13.3. Pre-paid SIM card balance
It is recommended not to use prepaid cards in the car alarm. If you
have no other choice than prepaid cards, you can enable the CREDIT
instruction by the following sequence:
MASTER CREDIT uuu..u xx
where: uuu…u is the provider’s code to obtain the balance
xx is the time period (in da ys) for regular checking
yyy is the threshold level below
reported to the user (TEL1)
zz is the position of the first digit of the balance in the reply
SMS from the provider
After this sequence has been sen
the balance automatically every xx days and if the balance is lower
than yyy the user will be notified (TEL1)
If the CREDIT instruction is enabled in the above way, the user
can also obtain the current balance by the instruction CREDIT
To disable the automatic balance checking set the time period “xx” to 00.
13.4. Roaming
If you travel abroad and your SIM card supports
will work there too except for the LOCATOR and CREDIT functions and
the GPRS data communication which will not be available.
13.5. Reset
If you need to disconnect and then r
network, then use the
This does not affect a
charging up credit
13.6. Service
The DINFO instruction allows you to obtain current settings,
information about the quality of the GSM signal, the registration code for
GSMLink devices and some other parameters. This command always
requires the Master code.
Example of instruction: MASTER DINFO
Example of response: Car alarm reports: CA-1803
LV:03, RK:ABCDE-12345-FG67, R:01, GSM:25, GPS:5, Time:3.2.06
11:35
CA-1803A car alarm version
SN:123456 identification number of the product
SV:01 software version
LV:03 language
RK: ABCDE-12345-FG67 registration code for GSMLink
R:01 current Reset mode of the device
GSM:25 instant quality of GSM signal (ranging from 0 to 32 (best))
GPS:5 number of visible satelites (0-16)
14. AUX
AUX output can be set to the following mode.
AUX bus – this mode allows you to connect up to four CR-11A
modules to the bus. This enables you to extend car alarm functionality
via the power output. There are
can be operated by pressing two buttons together on the key fob RC-8x
(see instructions to CR-11A), or usng SMS instructions. This allows you
to operate independent heating, refrigera
car must not be immobilized by use of this module, because the output
reacts to incoming SMS instructions in every state of the car alarm, in
particular, while the car is on the run, thus possibly not under the user’s
control which could cause a traffic accident.
Instruction Status
AUXA (B) Relay switches on for 1 second
AUXA ON (OFF)
AUXB ON (OFF)
ON - Switch on permanently*
OFF – Switch off permanently*
AUXA xxM in xxxS
AUXB xxM in xxxS
xxM – numeric value of requested
duration of the relay to be switched
on, in minutes
xxxS – as above, in seconds
Example of an instruction to switch B relay on for 30 seconds:
AUXB 30S
* Maximum switch-on time is 60 minutes.
* If a relay (A or B) is sw
addition, the A r
disarming.
15. The back-up battery
To handle an absence of supply voltage in the car (disconnecting the
main battery, deliberate damage etc.) the car alarm is equipped with a
BB-02 backup battery. The battery supplies the car alarm when no
supply voltage is present (for 5 hours minimum).
siren, the BB-02 backs-up all the functions of the car alarm. The car
alarm is supplied with a small current from the BB-02. Fully charging a
fully discharged battery requires 5 days. In the case of a supply voltage
outage, the BB-02 starts to generate a voltage either for th
duration or until it is completely discharged. While testing it or being
handled, it is possible to protect the backup battery from being
completely discharged by briefly shorting the BB-02’s terminals (the BB-
02 has to be disconnected from the power supply). This causes
disconnection of the electronics inside the back-up battery. In the case of
switch-over to BB-02 operation (after a voltage drop under 8.5V o
complete disconnection of the battery), an SMS will be sent with
information about backup battery operation. An SMS
after the recovery of the main power supply voltage (at least 10
minutes).
16. Emergency
In the case of an emergency, when no installation MASTER co
available, it is possible to perform an emergency RESET of the car alarm
even without the code. Such a reset causes the car alarm to be set to
