Immobilizer CA-322 „Accent“ 2 / 1 MDF532 05
Immobilizer CA-322 „Accent“ - instructions
The „Accent“ brand name system is suitable for all cars equipped with 12V v
and a negative ground. The CA-322 immobilizer is remotely controlled. RF
communication is protected by a FLOATING digital code and by an ANTI-SCAN
feature.
Arming and disarming of the system is confirmed by the turn indicators blinking.
While the ignition key is on, the system can not be armed. This protects the car from
having the system accidentally
of the immobilizer is provided by an LED indicator.
Door lock outputs allow the central locking
control (programmable output pulse duration). A signal to close electrically powered
windows is also av
An automatic Dome light control is provided by an ex
(negative trigger). It turns ON the dome light after disarming and the opening of
door. The light will remain ON until you sw
A built in powerful immobilizer (3 relay
(starter, ignition, electrical fuel pump etc.).
The „Accent“ provides optional REARM and AUTOIM
if the car has been entered within one minute of disarming.
automatically rearmed and the doors are locked again. AUTOIMMO function will block
the car automatically if ignition key is turned off for more than 5 minutes. Optional
functions can be modified in setting mode by a professional mechanic after installation.
SPECIFICATIONS
voltage 10 - 16VDC
stand by consumption max.
working temperature -40 to +85°C
remote controller distance max. 20m
remote controller equipped with SAW resonator
coding digital floating code system with Anti-scan
turn indicator outputs 2 x +12V, max. 2 x 5A
central lock outputs pulses to GND, max. 300mA, 0.3 - 4sec.
optional „lock“ signal duration (for el. powered windows) 60sec.
immobilization relay contacts (3 loops) max. 15A permanently
max. 20A for 30 seconds
AUX output digital bus output (future use)
negative switched door contacts input / courtesy light output 10W
AL1 negative input / dome light output
VALET push button executive override, setting
All the data is stored to EEPROM memory.
This product complies with IEC 839-10-1, EEC No. 97
Hereby, Jablotron Ltd., declares that this CA-322 is in compliance with the essential
requirements and other relevant provisions of Directiv
conformity assessment can be found at the web page www.jabl
, section
Technical support.
Note: Although this product does not contain any harmful ma terials we suggest you
to return the product to the dealer or directly to the producer after usage.
INSTALLA
The immobiliz
system can result in poor and or dangerous car performance. We recommend
having the immobiliz
INSTALLA Disconnect the battery before starting
installation. Keep in mind that if your car has some memory functions, these
may be erased if you disconnect the battery
equipped with airbags when connecting or disconnecting the battery. R
the car owners' manual before disconnecting the battery.
Install the control unit in the passenger compartment. The recommended
location is under the dash board. The wire coming
the remote control antenna. The
working distance. Ideally, the w
the car, be sure to check the area before drilling to prevent damage to the car.
LED indicator is on a separate cable. Once you have determined the
position on the dashboard where you w
diameter hole in the dashboard
cables before you drill the hole. Connect the LED cable into any of the three
pin connectors on the main unit .
VALET Switch - has a separate cable. This push button switch can be used
as an executive override if the remote control is lost. How
switch was optionally
Find a hidden place in the car and install the switch. Connect the cable to any
of the three pin connectors on the main unit.
WIRING - route wires for the immobilizer with the
Check each connection made to ensure that it is solid and properly
Use only a real crimping tool to make connections. Complete and check all wiring
before switching on the power. Each w
(remove the numbers after installation).
1 = Positive Supply - connect this wire to a direct line from the
terminal of the battery. This wire is split in the immobilizer
loop with the fuse (10Amp), is a separate power supply for turn lights. The
fuse protects against a short connection of the turn indicator bulb. Use only
a 10A fuse in this harness!
2 = Grounding - connect this wire to the original GND
4 = „Lock“, 5 = „Unlock“ - these wires provide signals to control the central
door lock system. The max
300mA. NPN transistors sw
The duration of output pulses is programmable (0.3sec. factory
Connect the wires from the „Accent“ to the inputs of the central locking sy
control unit.
If the car has powered windows wi
use the „Lock“ signal to close all the windows. In this case, select the
“Locking Signal“ in the setting mode This w
doors and will close all window
only lock the doors if button B (2) is used.
Do NOT connect the wires from the immobiliz
"Examples of Accent use for different central locking systems" if your locking
system uses another type of
a central locking system in your car, we recommend the CL-20A.
6 = Ignition Key Input - connect this w
when ignition is ON). This signal wevent accidental arming of the sy
while driving. This signal is also used for R
Note: Be sure, that +12V is also present, when a starter is used.
7 = Door Switches input, Dome Light Control output - is a negative
input for REARM function. It also functions as the dome light control output.
Connect this wire to the door sw
in all doors). With the system is disarmed, opening the door turns
dome light till the ignition key is switched on (max
Note: The maximum load of the interior light can be 10W.
8 = AL for REARM function and dome light controlling. It
can be used for trunk switch.
13 and 14 = Turn Indicators - the two wires provide pow
right turn indicators. Each wire prov
a
left turn light and the other wire to the right turn light.
Immobilization - the six wires in a separate connector are the three built-in
immobilization contacts’ leads. The following wires are connected
relay contacts inside: 1-3, 2-4, 5-6. The starter, fuel pump, ignition or any
system that when electrically
be connected here. Only disarming the system and switching O
ignition closes the contacts. These contacts will operate correctly
load up to 15A, max. 20A for 30 seconds (each).
Adding of a new remote controller
There are two remote controllers in each „Accent“ immobilizer set. The sy
can be operated with a maximum of three remote controllers. T
additional remote control or to replace an original one (in the case one is lost)
perform the following procedure:
Switch on the ignition key
VALET button fiv
ignition). The turn indicators will make two long signals and the LED will light
continuously. The control unit is now in remote control learning mode.
You must activate all remote controls (one by one, button A, B, 1 or 2) which y
want accepted by the immobilizer. The control unit will store codes in its memory
(confirmed by a LED flash and for a brand new
Keep in mind that only three controllers can be taught to the
you try to teach a fourth controller, the first one w
you activate only
the system only w
To close learning mode, switch off the ignition key. You can see how
remote controls are available for your immobilizer by number of LED
time when you sw
Setting mode
Optional functions can be modified. To enter the setting mode
following procedure:
• press the hidden VALET
and hold it pressed
• after 5 seconds (or more) switch on the ignition key
• the turn lights will make one long and one short signal and the LE
continuously
• release the VALET button; the immobilizer is now in setting mode
Now you can make setting; see the follow
Setting of the parameter is indicated by LED and can be changed
control button (A or B), each short pressing will change the parameter (on - off
- on - off - etc.). Bold printed parameters are factory default settings.
To select next parameter (nex
The turn lights will confirm parameter (row
Step by step go through all parameters. When you are on parameter number
5
and the setting mode will be exited (confirmed by the turn lights w
signal). If you switch the ignition key
completed, the setting mode will be terminated and no changes will be stored.
Note: All d
immobiliz
no. parameter (on) status (LED) l (off) description
1 REARM enabled
disabled if car is not entered within 1 min. after disarming, it will arm again
2 AUTOIMMO enabled
disabled if enabled it will block engine if ignition key
3 duration of locking pulses 0,3 sec.
4 sec. modify „lock“ and „unlock“ output pulse duration
4 longer „lock“ si
60 sec.
normal
the „lock“ pulse is normal (see step no. 3) or longer (60 seconds)
5
emergency disarm with VALET
enabled
disabled
if emergency disarm is disabled, VALET button can only
disarm is possible only by a professional mechanic)
