CL-305 Click remote control 1/2 MHK51204
The CL-305 „Click“ remote control system for central locking
The CL-305 “Click” remote control system can be used for the control
original central locking control unit, the remote control of powered windows, the
servomotor of a fifth door, boot, etc. The remote control can
directly controlling servomechanisms. It is suitable for cars with 12V and negativ
grounding. The main unit is designed for installation in the car interior. It
protected against reverse polarity and incorrect connector insertion.
compatible with RC-4x remote controls. Communication is secured by floating
codes. Up to four remote controls can be enrolled to the receiver.
The CL-305 Click remote control has selectable functions such as re-arming,
selectable pulse lengths, and double pulses. The device can also
simple security system to prev
Installation:
SIR (ysiren output, sw (max.1.2A).
PGM (blue-white) –programmable output switc (max. 300mA),
we recommend providing the P
It can be set to two modes. (se
- IMO, the electrical circuits (ignition, fuel pump etc.) of the car can be
immobilized when the car is locked. If the car is
the immobilization relay copies the ignition key.
- BOOT, pressing the button generates a 0.5 sec signal to open the boot.
LCK_IN – NC
ULK_IN – NC
DOOR (greydoor switch input. It reacts to connection to ground.
KEY (blue) – ignition key
BLR, BLL (pink) – to confirm locking/unlocking of the car by a
signal from the turn lights
(+12V, max. load 2 x
Power supply +12V (red) - connect directly to the battery
GND (black) – connect to the original grounding in the car.
LNO (red-green– pow
relay outputs (max. load 15A
UNO (red-blue), UNC (black-blue), UC (white-blue) – power unlocking
relay (max. load 15A
1
8
916
+ 12
"1
+
12 V
rel
ma
sire
max. 1,2
ignition
key
door
contact
turn lights
max 2x 5A
UC
LC
UN
UN
LN
LN
inputs
relay output
unlock (
+
12 V
+
12 V
15 A
PGM
SI
LCK_IN
KEY
ULK
DOO
GND
+12 V
LNO
LNC
UN
UN
LC
UC
BLR
BLL
C -
NO
NC
Alarm function – intruder alarm signaling
The CL-305 Click remote control can be used as a simple car alarm. When the
car is locked and the selectable ALARM function is set
KEY inputs are monitored. (30 sec after locking the car). If
SIR output will be activ
If the car is unlocked by key then the alarm will be triggered. To stop the alarm it
is necessary to unlock remotely. If there had been an intruder alarm during
time when the car was locked, three siren chirps w
will flash during disarming.
Operation
In the factory default setting (PGM output set to IMO of
the remote control is used to lock the car and button to unlock the car. If
the PGM output is set to BOOT mode, then the button is used for both
locking and unlocking. When pressing the button, a 0.5 sec
generated to open the boot.
Enrollment of the remote controls
Up to 4 RC-4x remote controls can be enrolled to the CL3
must be enrolled to the unit in the same session. By enrolling a new remote
control later, all the existing controls are erased.
• Unlock the car and disconnect the CL-305 from its power supply
• Switch the ignition key
• During a period of 30 sec. turn the ignition on and off 3 times, in 2 seconds
the turn lights (flashers) will then give a
mode entry.
• Press any button on the remote control. Enrolling of the remote control is
confirmed by a turn light flash.
• Enroll all the remote controls (up to four) successively
• To finish enrolling, switch the ignition
long.
Programmable functions
The CL-305 Click remote control has 8 programmable functions, described in
the following table.
To enter programming mode:
• Unlock the car, sw and disconnect the
control unit from the power supply,
• After 1 minute reconnect the control unit to the power supply,
• During a period of 30 sec. turn the ignition key on and off 5 times. n
2 seconds the turn lights (flashers) will flash once to confirm programming
mode entry.
• Programming always starts in programming position The status of the
current parameter is indicated by the turn lights (lit or unlit). A parameter
be changed by pressing the button on the enrolled remote control
• To
off. The position is indicated by the number of turn light flashes
• To exit programming mode, go through all the parameters and turn
ignition on and off – it is confirmed by a long turn light
programming mode will be terminated automatically in 120 seconds)
Specifications:
Power supply 9 - 15 V
Stand-by con 6 mA
Maximum current consum 180
Working tempe -40 to +85 °C
Enclosur
Jablotron Ltd. declares, that the CL305 remote control system complies w
essential requirements and other relevant provisions of
and Directive 1989/336/ES. The original of the conformity
found on www.ja , Technical Support section.
Note: Although this product does not contain any
we suggest you to return the product to the dealer
producer after use.
Note: Thbold values in the table are the factory default setting.
Turn lights
Position Function
Unlit Lit
Description
1.
Central locking
ELEC
PNEU
In ELEC mode, the pulse length is 0.5 sec. In PNE
3 and 4 have no effect.
2.
WIND
no
yes
To prolong the last locking pulse to 30 sec.- only v This parameter must not be
set to y
3.
DLCK (double
locking pulse)
no
yes
Double locking pulse (first 0.5sec. pulse – 1sec. pause – second 0.5sec. pulse). Only v
mode
4.
DUNL (double
unlocking pulse)
no
yes
Double unlocking pulse (first 0.5sec. pulse – 1sec. pause – second 0.5sec. pulse). Only v
mode
5.
REARM
no
yes If the car is not entered w
6.
CHIRP no
y
Audible siren chirps (if locked one and if unlocked, two chirps can be heard)
7.
PGM
IMO
BOOT PGM output can control the immobilization relay or central locking of a BOOT.
8.
ALARM
no
yes Intruder alarm function
